Comparison Hatsan BT65 SB Elite vs Hatsan BT65 RB Elite

The muzzle energy provided by the rifle.

Muzzle energy is the kinetic energy of the bullet at the exit from the barrel. This energy, in turn, depends on two factors: the mass and the muzzle velocity of the bullet. Thus, this indicator directly describes the overall power of the rifle: higher muzzle energy allows you to effectively fire at longer distances and/or heavier ammunition. On the other hand, an increase in power accordingly affects the cost of weapons.

Note that muzzle energy can be grounds for legal restrictions on the purchase/use of pneumatics. So, in some countries in the post-Soviet space, the maximum value allowed for freely sold rifles is 7.5 J — a special permit will be required to purchase more powerful weapons. And most freely sold rifles in such regions have a power of the order of 3 – 5 J. Such legal restrictions should be clarified separately. Lower rates are found mainly among “soft” pneumatics for airsoft (airsoft), using 6 mm plastic balls. For such models, a value of more than 2 J is already considered very solid, and in games such rifles are used with a minimum distance limit — for example, 15 m or 20 m (so that a shot from too close a distance does not injure the player).

It is also worth saying that the claimed characteristics of air rifles may, at first glance, not correspond to physical calculations. For example, for a model for the same...7.5 J, the initial speed of 250 m/s can be claimed in the characteristics; for a 4.5 mm bullet weighing 0.5 g (the average, most popular weight), this would correspond to an energy of as much as 15.6 J. However, there are no inconsistencies here: such characteristics mean that the muzzle velocity was measured for a lighter bullet (for example, 0 .2 g), which accelerates more strongly at the outlet of the barrel. Accordingly, with heavier ammunition, the speed will be lower; it can be determined using special formulas or online calculators.

The type of cocking system provided in the design of the rifle.

The cocking system is responsible for placing the trigger mechanism on the combat cocking (in the position of readiness for firing), and with a multi-shot design, it is also responsible for sending the next bullet into the chamber. Such systems are usually divided according to the method of control. Variants found in modern times include but are not limited to barrel fracture, lever ( side or underbarrel), pump action, bolt action (including varieties such as biathlon and bolt action), and autococking. Here are the main features of each of these systems:

— Fracture of the trunk. In rifles with this type of cocking, the barrel is fixed on a rotary axis, and folds down with each reload. In this case, not only the trigger is cocked, but the chamber is also opened, allowing you to load the next bullet. This option is found exclusively in spring models — conventional and with a gas spring (see "Type"), it is with such rifles that a barrel break is best compatible. One of the key advantages of such systems is their low cost. In addition, breaks are very easy to use, do not require special skills and are s...uitable even for inexperienced shooters. So such pneumatics are extremely popular nowadays. At the same time, it is usually made single-shot (with very rare exceptions), constant folding and unfolding of the barrel can be quite tedious, and the barrel mount tends to become loose as it wears, which reduces accuracy and power.

— Autoplatoon. Systems that do not require the shooter to take any additional actions to cock the weapon; found in PCP pneumatics (see "Type"), gas models, as well as AEGs (the latter, by definition, are made only by auto-cocking). In accordance with the name, a platoon in such weapons is carried out automatically before each shot — usually, with sending the next bullet into the chamber (although there are also single-shot models where the bullet must be inserted manually). Anyway, auto-cocking is extremely simple and easy to use. In addition, on the basis of such mechanisms, even fully automatic weapons can be created (see "Automatic mode"), although most rifles with this feature still work in the single-fire format. Among the disadvantages of such systems, one can note the complexity of the design and rather high cost, as well as the fact that air / gas is additionally consumed for the operation of the auto-cocking. This reduces the number of shots per charge, and can also reduce the initial speed compared to similar models with manual reloading (however, the latter is predominantly characteristic of gas-balloon rifles).

— Underbarrel lever. Systems that use a lever under the barrel, which must be pressed down with each cock. Like the barrel fracture described above, this method is used mainly with spring-piston mechanisms and gas springs. It is more convenient and reliable, since the barrel of the rifle constantly remains motionless, there are no fasteners in its design that can loosen up and fail. On the other hand, the lever design is noticeably more complicated and more expensive than the tipping one, and therefore is quite rare.
Note that the inflation lever in multi-compression models (see "Type") is usually not responsible for cocking the weapon, so a different cocking method is indicated for such rifles (although there are exceptions). And in gas-balloon models there is a special kind of underbarrel lever — the so-called Henry brace, as in classic cowboy hard drives (in fact, such pneumatics usually just copies this weapon).

— Side lever. Systems using a lever on the side of the rifle — usually on the right. They are found mainly in models with a spring-piston mechanism or a gas spring. As in the case of the underbarrel lever, the main advantage of this method can be called the immobility of the barrel, which contributes to accuracy and reliability. On the other hand, such a cocking system is usually made for right-handers and can be uncomfortable when firing from the left shoulder; in addition, the side lever is somewhat more difficult to fit into the design than the underbarrel. Therefore, this option is not widely used.

— Shutter. Systems using a classic type bolt handle — sliding back and forth. This cocking does not provide air pumping, and therefore is used only in gas-balloon type rifles, PCP, and some multi-compression models (see "Type"). Pneumatics with shutters are mainly made multi-charged — this is the very idea of \u200b\u200bsuch systems (feeding the next bullet from the magazine); however, there are exceptions. In general, this is a fairly simple, practical and reliable method of cocking, however, nowadays, more specific types of shutters are increasingly being used — biathlon and bolt; they are listed separately in our catalog and described below.

— Biathlon shutter. A variety of bolts (see above), copied from small-caliber biathlon rifles. In such systems, as in traditional bolt mechanisms, the cocking handle is located on the side and moves back and forth. The key difference is that this handle is mounted on a swivel mount and, when reloading, does not slide along the guides, but swings on the axis. The biathlon bolt differs from the side lever of a similar design (see above) in its location (in the rear of the rifle), the shorter lever length, and also in that it does not provide air pumping. Many shooters find this shutter more convenient than the classic one — in particular, it has a very small operating force, so you can move the lever without looking up from the sight. And in some models, for cocking, you don’t even need to remove the “shooting” hand from the handle — just hook the lever with your index finger, pull it towards you with a slight movement of your wrist, and then, if necessary, move it forward with your thumb. The biathlon action is used almost exclusively in PCP rifles (see "Type").

— Bolt lock. A kind of bolt (see above), which, when reloading, not only moves back and forth, but also rotates around its axis — similar to how it happens in many classic firearms like the Mosin rifle or Remington 700. Actually, the similarity with a real weapon this is precisely one of the key advantages of such systems: they are appreciated by fans of traditional rifles, and can also be good simulators for developing basic shooting skills from more serious "bolt" weapons. Most pneumatics with such cocking systems are PCP or gas-balloon, only a few models use the multi-compression principle (see "Type").

— Pump mechanism. Systems that use a movable handguard for cocking — like pump-action shotguns, hence the name. The main convenience of such systems is that cocking can be carried out without removing the hands from the weapon. On the other hand, the constant movement of the forearm knocks down the sight and adversely affects accuracy, so this method of cocking is not very popular in air rifles.

Volume of the compressed air tank installed in the PCP rifle (see “Type”); if there are two tanks (see below), their total capacity is usually indicated.

A large tank allows for a greater number of shots per fill, but there is no strict dependence here: this number will also depend on the pressure in the tank, muzzle energy and some other specific factors. So in this sense, the tank capacity is purely for reference. But what it directly affects is the dimensions and weight of the weapon: a larger container will inevitably weigh more and take up more space. However, the latter drawback is often compensated for by the large length and small diameter of the reservoir - such a detail fits well into the proportions of the rifle.

As for specific volumes, they can vary up to 60 – 100 cm3 in relatively simple and inexpensive rifles up to 500 cm3 in high-end models; and if there are two tanks, their capacity can exceed 800 cm3.

The type of sight the rifle is originally equipped with. Note that many models allow the installation of other sights — in addition to standard sights or to replace them. And the optics or collimator can initially be combined with a mechanical sight (front sight + rear sight), which in such cases plays the role of a spare. However, these features are not available in every rifle, so when choosing, it is best to focus on the type of complete sight.

Nowadays, in addition to the traditional sighting bar with a front sight, in air rifles you can find diopter, optical and collimator sights, and in some models regular sights are completely absent. Here are the features of each of these options:

— Aiming bar and front sight. Devices in the form of a front sight and a rear sight, which has the form of a horizontal bar with a slot; when aiming, you need to combine these devices so that the front sight is visible exactly in the middle of the slot and flush with its edges. Such sights are extremely popular in modern pneumatics: they are as simple as possible, inexpensive, compact and reliable, besides they do not depend on batteries and are quite resistant to shock and shock. In addition, the front sight with a bar is not as restrictive as an optic or a collimator, and is better suited for shooting at moving targets....The main disadvantage of this option can be called the fact that effective aiming requires a certain skill — after all, you need to control not only the aiming itself at the target, but also the relative position of the front sight and the slot. On the other hand, this moment can turn out to be a virtue — in particular, when learning to shoot: having learned how to shoot effectively with such devices, the shooter will feel quite confident with other types of sights. It is also worth noting that the front sight does not give any magnification — this makes it difficult to shoot at small and/or distant targets; however, again, this feature is not always a clear disadvantage.

— Diopter sight. A kind of mechanical sighting devices (that is, front and rear sights), using the diopter principle of operation. The rear sight in such devices is a plate with a small hole through which the shooter looks at the front sight. Such a rear sight is easier to use than a traditional slotted rail, especially for beginners: even without special skills, the shooter subconsciously chooses the position of the eye in which the front sight will be in the centre of the hole (as it should be when aiming). In addition, the small aperture gives a slight zoom effect and enhances target definition, which is especially important at longer distances. On the other hand, diopters noticeably limit the view, are poorly suited for low-light conditions and are easily clogged with various contaminants. Therefore, this type of sight is used extremely rarely in pneumatics — mainly in powerful long-range rifles, mainly for sports purposes.

— Optical sight. Traditional optical sights in the form of a "spyglass" with a reticle applied in the field of view of the shooter. Initially created for high-precision long-range shooting, mainly at fixed targets; in the same role are used for pneumatics. However not every air rifle with optics is a powerful long-range weapon — there are also relatively “weak” models. But even such pneumatics can be a good training tool for high-precision shooting: a small distance in this case can be compensated for by a small target size. On the other hand, optics significantly affect the price of the rifle and require careful handling. Of its features, it is also worth noting that such sights necessarily have a certain magnification; due to this, they allow you to better consider small targets at the same time limit the field of view. It should also be borne in mind that optics are not well suited for offhand shooting and require careful insertion: the eye must be exactly on the optical axis of the sight, otherwise the aiming point may not coincide with the point of impact.

— Collimator sight. The working part of a collimator sight is a glass window onto which a luminous aiming mark is projected using a special optical system — a dot, crosshairs, a circle with a dot, etc. Sights of this type usually do not have magnification and are intended for shooting at short distances, including on moving targets and offhand. So in application, the collimator is similar to the front sight with the whole; and its key advantage lies in ease of use: no need to combine the front sight and the slot, just find the aiming mark in the window and aim it at the target. At the same time, unlike optics, it is not necessary to keep the eye strictly opposite the centre of the sight: the parallax effect (see "Adjusting parallax") in collimators is very weak, if not absent at all. The main disadvantage of this type of sights is that they require batteries to operate; in addition, collimators are noticeably more expensive than traditional mechanical sights, and also require more careful handling (although they are still less delicate than optics).
It's worth noting that these attachments are especially popular with airsoft guns like most AEGs (see "Type"): collimators are great for fast-paced fights.

— Is absent. The absence of any sighting devices in the original delivery set — there are only mounts for installing such devices. See below for more details on the different types of fasteners; here we note that such equipment does not allow the use of a rifle “out of the box”, however, it makes it possible to choose a sight for it at your discretion, without relying on the choice of the manufacturer. This is especially true if you plan to use optics — nowadays a wide variety of such sights are produced, for different tasks and usage scenarios. Actually, most air rifles without a scope are designed just for the installation of optics, although the possibility of using collimators is often also allowed; and in airsoft pneumatics, removable front sights with rear sights are also used.
It is worth noting that spring-piston rifles and models with a gas piston have a specific double recoil, which not every sight is able to transfer — even if it can be used with powerful firearms. So when looking for optics or a collimator for such pneumatics, you should be especially careful — for it you need to choose sights that were originally designed for such rifles.

The type of mount for mounting sights provided in the design of the rifle. Most often in such cases we are talking about an optical or collimator sight; and the most popular mounting options are Weaver/Picatinny rail and dovetail. Here are their features:

— "Dovetail". This type of mount has a cross-sectional view of an inverted trapezoid (expanding upwards); the clamp on the sight covers this trapezoid from two sides, and the transverse cutouts, unlike the Weaver / Picatinny rails, are not provided for in the design — fixing in place is carried out in other ways. Dovetail mounts were originally used in civilian hunting rifles, as well as in Soviet-style military weapons. Nowadays, due to their simplicity, low cost and versatility, they are extremely common in air rifles. In addition, we note that you can even install a Weaver / Picatinny rail on a dovetail (such rails are available separately) and use a sight with the appropriate type of mount.

— Weaver / Picatinny rail. Fastening in the form of a bar with a T-shaped profile and characteristic transverse slots — they serve to rigidly fix the installed accessories in one place. Technically, Weaver and Picatinny rails are different types of mounts, they differ in the size of the slots; these differences are such that the sights and other “body kit” for the Weaver rails easily get on the Picatinny rail, but the opposite option is f...ar from always possible. However, in the civilian market, most weapon accessories for such slats are made specifically for the weaver, so this nuance, most often, is not fundamental, and both types of slats are combined into one category.
In general, for a number of reasons, such straps are much less common in air rifles than the dovetail. At the same time, classic pneumatics are most often equipped with Weaver mounts, but in airsoft copies of real weapons, Picatinny rails (or compatible NATO STANAG 4694 rails, also known as RIS 22 mm) can also be used.

— Is absent. The absence of any standard mounts for the sight in the design of the rifle. Most often, this designation means that the rifle is equipped with a classic front sight with a whole and does not require the installation of additional sights. However, there is also a more specific option — pneumatics, in which original mounts are used to install optics or a collimator, which are not related to the standards described above. Such rifles can be supplied with or without scopes; there are even models with non-removable optics, although extremely rare.

The degree of magnification provided by the rifle's complete optical sight; for models with variable magnification, the entire adjustment range is indicated, for example 3 – 9x.

For sights of this type in general, see "Aiming Device". And several points depend on the degree of increase at once. On the one hand, a higher magnification allows you to better see small and/or distant targets and facilitates high-precision shooting; on the other hand, it limits the angle of view and significantly affects the cost of the sight, and sometimes also its dimensions and weight. And since air rifles are mostly not designed for long distances, the magnification of complete optics in them usually does not exceed 9x, and one of the most popular options is 4x. However, there are exceptions: in powerful high-end pneumatics, you can find sights with a maximum magnification of 24x and even higher.

Actually, the manufacturer most often selects the magnification of optics for the ballistic characteristics of the rifle. So, when choosing this parameter, it often turns out to be secondary, and it makes sense to focus primarily on the muzzle velocity of the bullet and the firing range for which the weapon is designed — usually, the capabilities of complete optics are quite enough for this. It is also worth mentioning the variable magnification sights mentioned at the beginning, which are quite common nowadays — they are somewhat more complicated and more expensive than fix...ed optics, but they allow you to adjust the magnification to the specifics of the situation.

The diameter of the front lens (objective) in the optical sight, which is equipped with a rifle.

For sights of this type in general, see "Aiming Device". And the diameter of the lens depends primarily on the amount of light entering the scope. Thus, other things being equal, a larger front lens produces a clearer and brighter image; this is especially noticeable in low light. On the other hand, a larger lens is noticeably more expensive, and it also affects the weight and dimensions of the sight; and in bright daylight, the difference from the “smaller” optics may not be fundamental. In addition, recall that the actual image quality is determined by a number of other factors; as a result, high-end optics with a relatively small front lens may well be more effective than a large low-cost model.

In view of the foregoing, it is worth paying attention to the diameter of the lens in cases where the sight is planned to be used in low light conditions — in a dense forest, at dusk, etc. In this case, it is worth considering not only this indicator, but also other features of the optics (and it is best to focus on practical reviews). If the rifle is bought for recreational use in the daytime in good light, the size of the lens will be a purely reference parameter: in such conditions, almost any optical sight works normally.

The ability to manually adjust the parallax in the complete optical sight of the rifle.

For sights of this type in general, see "Aiming Device". Parallax is a phenomenon that occurs when the shooter's eye is not on the optical axis of the sight (in other words, not strictly in the centre of the eyepiece). In such cases, the reticle in the eyepiece may also shift, and its apparent position may not coincide with the actual aiming point. To eliminate this effect, parallax adjustment is applied.

Any optical sight undergoes such adjustment at the factory. However, the physical features of this phenomenon are such that parallax can only be adjusted for a certain distance to the target; with significant deviations from this distance (more than 30% downward or 60% upward), parallax again begins to appear. So if you plan to use weapons at different distances, then it is best to have a sight on it with manual detuning from parallax. At the same time, it is worth noting that the complete optics in air rifles are usually adjusted to relatively short distances — at which these weapons are used; and deviations from these distances are rarely significant. Therefore, the parallax adjustment in standard pneumatic sights is rare — mainly among powerful long-range models that can deal with a wide variety of distances.