Comparison Hansgrohe Logis 71100000 vs Hansgrohe Focus 31607000

Distance from the fixing point (for vertically mounted taps) or from the centre of the mounting hole (for horizontally mounted taps) to the middle of the spout. It is a characteristic that determines the "reach zone" of the tap.

The jet height is usually specified for taps with horizontal installation (see "Type of installation"). It is measured from the base of the tap to the spout outlet. The large height of the spout is important primarily for kitchen models (see "Suitable for"), because it allows you to place large dishes in the sink. This parameter is directly related to the height of the spout (see above): the height of the jet cannot be greater than the height of the spout. Thus, in fact, one has to find a compromise between the height of the jet and the dimensions of the tap, especially if there is little space for its installation.

The angle of the water jet produced by the tap, relative to the vertical. Generally stated for full head; with partially blocked water, this angle is smaller. Anyway, the water jet is usually directed towards the user, and the greater the angle of inclination, the farther from the spout the point of incidence of the jet will be placed. However, in most cases this point is not critical; problems can arise only in very cramped conditions, with small basin sizes.

The functions of the tap are mainly design features, among which the are check valve, bottom valve, cold start, LED backlight, temperature adjustment lever, display, auto-drain (hygienic flush), washer/dishwasher switch< /a>, shelves for accessories. In more detail:

— Check valve. The non-return valve prevents the flow of water through the tap in the opposite direction — for example, when there is a large pressure difference between hot and cold water. This function will be relevant for those who are going to install water metres: the presence of check valves on mixers is often a prerequisite for fulfilling an application for installation, because such valves prevent counters from spinning in the opposite direction. In addition, you should pay attention to the presence of a check valve in the tap (especially a single-lever tap, see "Tap type"), if there are interruptions in the water supply of your house — such taps behave much better in case of pressure surges in the water supply.

— Drain valve. A device that allows you to close the drain hole in the sink, kitchen sink or bidet (depending on the purpose of the tap). There are two types:
...
— Lever drain valve. To control the operation of such a valve, a small lever is used, located behind the tap, on the side of it or in front of the body. Raising and lowering it opens and closes the drain plug in the sink.

— Pressing drain valve. Valves of this type are locked and unlocked by pressing the drain plug, for which you need to wet your hand.

— Cold start. A feature found exclusively in single-lever models. The general principle of operation of the “cold start” is as follows: if you open the tap with the initial position of the joystick, it will not bring out mixed warm water (as in more traditional single-lever devices), but only cold water. To add hot water and raise the temperature, you need to deflect the lever from its initial position. Such a format of work can provide significant savings: by default, cold water comes out of the tap, and hot water is added to it only if necessary.

— LED light. Lighting system based on LEDs — an efficient and economical source of illumination. The purpose and functionality of such a backlight may be different. So, in some models, it is installed on the spout and directed downwards, which allows you to clearly see the space under the spout even in low ambient light. Sometimes such illumination also illuminates the stream of water, giving it an unusual appearance. There are also quite original systems — for example, with a transparent spout and LEDs at its base, which creates the effect of a tap glowing from the inside; and in some models, the lighting also changes color depending on the temperature of the water. However, anyway, this feature significantly affects the cost, so it is typical mainly for premium products.

— Autodrain (hygienic flush). Such a system is equipped with taps with additional electronics — mostly contactless models, as well as products with a thermostat or a button switch. The autodrain works as follows: at a certain rate (for example, once every 12 hours or once a day), the automation briefly turns on the water. Due to this, harmful bacteria are washed out of the device, which tend to multiply on the inner surfaces of the spout and in “stagnant” water inside the tap itself. At the same time, the consumption of water for hygienic washing is small, usually it is practically not noticeable against the background of general consumption.

— Temperature adjustment lever. A function found in taps, which design initially does not imply a temperature controller — primarily non-contact models, as well as in products with one main lever or with button activation (see "Tap type"). As the name implies, the temperature control lever allows you to use such a tap not only to control the pressure, but also to change the temperature of the water.

– Display. Taps that display temperature and/or current water flow. The display provides a clear visualization of the settings and allows you to see what kind of water and how much is flowing from the tap. However, the presence of the screen significantly affects the cost of the tap.

— Washer/dishwasher switch. A function that can significantly facilitate the connection of a washing machine or dishwasher to the water supply system. Taps with a washer/dishwasher switch have a separate pipe for connecting the dishwasher, as well as the switch itself, which allows you to open and close the water supply to this pipe. Thus, to connect a washing machine or dishwasher, you do not need to install additional bushings, splitters, etc. — just connect the device to an existing output. And you can control the water supply directly from the tap body, for this you do not need to get under the sink or into another hard-to-reach place.

— Shelf for accessories. Most often, the role of such a shelf is played by the upper part of the body, specially made flat. This feature is found mainly in bath and/or shower taps (see “Suitable for”): it is convenient to keep shampoos, gels, soaps and other cosmetic/hygiene products on the shelf.

Note that this function is rare — mainly in high-end taps (in particular, thermostatic ones), which initially have large body sizes. In more traditional models, it makes no sense to include this design element — it is wiser to purchase a shelf as a separate accessory for the bathroom.

The lowest inlet pressure at which the tap is able to fully perform its functions of unhindered water supply.

The highest inlet pressure at which the tap is able to operate in a trouble-free mode with minimal risk of premature failure. In other words, this is the ultimate strength of the tap. Note that for normal east european use, it can be assumed that the maximum pressure in the water supply is 6 bar. One should focus on that value and choose a model with a small margin of max pressure in order to avoid leaks in the tap nodes during pressure surges in excess of the norm. Note that in plumbing with a centralized water supply, the pressure can reach 10 bar. Therefore, for expensive taps that make high demands on the inlet pressure, it is necessary to buy special reduction gears.

The diameter of the holes required to install the tap. This dimension allows you to assess whether the tap will be compatible with a sink, wall, etc., what dimensions the additional parts should have to install it, and whether the holes will need to be widened or narrowed.

Type of additional finishing provided in the tap. This item can specify several options — this means that this model is available in different design options. And if the finishing material coincides with the body material, this means that there is virtually no additional coating; this is found, in particular, among taps made of stainless steel, which itself is quite resistant to corrosion.

In modern taps, the following types of finishing are used: granite, chrome, chrome with granite, chrome with gold, matte chrome, stainless steel (glossy or brushed), brass, nickel, copper, bronze, gold, as well as brushed in one color or another. Here are the features of each option:

— Granite. Granite is characterized by a pleasant appearance, moreover, it is available in an abundance of different colours, allowing you to choose a tap for the design of the kitchen. Of its advantages, it is worth noting high durability, absolute resistance to corrosion and good sanitary characteristics (prevents the growth of bacter...ia). The main disadvantage is the high price.

— Chrome. Chrome plating is applied to metal surfaces primarily for corrosion protection; it has a characteristic shiny (almost mirror-like) appearance. Chrome provides high resistance to oxidation and damage, yet looks good and is inexpensive — as a result, it is one of the most widely used coating materials. Its main disadvantage is the tendency to get imprints on it over time; their removal is associated with certain troubles.

— Chrome/granite. The combination of chrome and granite finish in one product. See above for more details about the features of each of these materials, but here we note that their combination implies the presence of different types of finish in different parts of the tap. Thus, the design acquires a more original and stylish appearance, greater hygiene and resistance to contamination than pure chrome, while being cheaper than pure granite. And from the point of view of the overall design of a bathroom or kitchen, it is this combination that in some cases turns out to be the best option.

— Chrome/gold. The combination of chrome finish with individual "gold" sections. The features of chrome are described above, and the "gold" elements give the product a rich appearance, while a fairly large number of buyers prefer this combination to the “solid gold” finish.

— Matte chrome. A matte variation of chrome finish (see above). On such a surface, dirt, and prints are much less noticeable than on a classic glossy; in addition, it may be more suitable in design or simply more pleasing to the eye than glossy. At the same time, the creation of matte surfaces is associated with certain difficulties, and therefore they are relatively uncommon.

— Stainless steel (glossy). Stainless steel finish is generally similar in characteristics to chrome — it is durable and resistant to corrosion. However, such a surface is somewhat different in appearance and for a number of reasons it is used mainly in premium-class models — including taps made entirely of "stainless steel" (such models, in fact, have no finish).

— Stainless steel (brushed). Similar to matte chrome, such steel is more resistant to dirt than glossy (see above), otherwise it is completely identical to it.

— Brass. Brass coating is most often combined with a body made of the same material (that is, there is actually no special finish in such a tap). One of the advantages of such a surface is a pleasant golden hue, which is especially suitable for retro-style taps. At the same time, the cost of such products for a number of reasons turns out to be quite high, besides, they are prone to the appearance of hard-to-remove prints. Therefore, they are quite rare.

— Nickel. In terms of characteristics, nickel finish is similar to chrome and is used for the same purposes, however, for a number of reasons, it is much less common than chrome.

— Copper. Finish of characteristic reddish color. Copper can give an “old” look even to a modern product, and for retro-style taps, it can be simply irreplaceable. On the other hand, this material is expensive, in part because it is difficult for copper to provide sufficient corrosion resistance.

— Bronze. Bronze is an alloy based on the copper described above and is used similarly — mainly to provide an authentic look to retro-style taps. The main difference between the two materials is the color — the bronze is somewhat darker, and the red colour is not as pronounced in it (although specific shades in different models can also be different). In addition, this material is easier to make resistant to corrosion, so bronze products are much more common than copper ones.

— Gold. Yellow alloy finish to imitate the look of gold. It is used to give the tap a rich appearance, while at the same time it is expensive in itself, as a result of which it is used mainly in premium models — in order to emphasize the level of the product even brighter. On the practical side, like any material of this level, it is characterized by high resistance to oxidation, but resistance to pollution and ease of cleaning can be different (although in most cases these indicators are also on top).

— Brushed. A brushed finish that is applied specifically to give the product a certain color — most often black or white, but other options are also found. Accordingly, the main advantage of this option is a non-standard appearance: with paint, you can achieve colors that are not available with other types of finish. At the same time, any paint perfectly resists corrosion, and the differences between different models of taps with such a finish are mainly in durability and scratch resistance. These characteristics, usually, directly depend on the price category of the product.

The height of the tap, measured from its base or lowest point to the highest point of the spout. The height of the spout partly determines the installation possibilities — in fact, this is the minimum vertical free space that is required for the tap. In addition, in models with horizontal installation (see "Type of installation"), the spout height is related to the jet height (see below).