Comparison ThrustMaster T150 Force Feedback vs Logitech G29 Driving Force

The length of the cable provided in the design or delivery set of the wired or combined controller (see "Connection").

In general, the meaning of this parameter is obvious: a longer cable gives more freedom of movement, but can create inconvenience at short distances. In fact, the length of the wire is important mainly in cases where a wired connection is used to play on a large screen: for comfortable viewing, it is desirable to be at a fairly large distance from such a screen. However, even in this case, a relatively short cable can be compensated for by the length of the wires going from the console (or other gaming device) to the screen, or even by connecting the set-top box to the screen wirelessly (many modern models have this capability). If the controller is used for a computer, this parameter can be ignored: the system unit or laptop is usually located in close proximity to the user, and even a fairly short wire is enough to connect.

The total number of buttons provided in the design of the manipulator.

The more buttons — the more additional features you can "tie" to the manipulator, the lower the likelihood that during the game you will have to turn to other controls (for example, a PC keyboard). However, many game consoles (see "Platform Compatibility") provide a certain minimum number of buttons for a compatible gamepad — a smaller number simply would not allow full use of all the functions of the console. For example, the original PlayStation 4 controller has 11 buttons.

Note that the D-Pad (see below) is not included in this calculation: it is considered a specific control, although it is based on buttons.

The presence of the D-Pad manipulator in the controller design; the type of such a manipulator can also be specified here.

D-Pad is used to move the character, cursor, etc. in strictly defined, standard directions. In some cases, this can be more convenient than using analogue levers that tilt to either side (see below). As for the varieties, nowadays there are such options:

— 4-position. The classic D-Pad, which appeared at the dawn of game consoles and does not lose popularity nowadays. Available as a set of 4 buttons in a distinctive cross-shaped layout, or as a single solid "multi-sided" button. Anyway, such a device provides 4 fixed directions: up, down, right, left. But to move diagonally, you need to select 2 corresponding directions at once; this is not always convenient, so in this regard, 4-way D-Pads are considered somewhat less practical than the 8-way ones described below. On the other hand, they are also quite functional, while being simpler in design, reliable and inexpensive; and strictly diagonal movements are not required as often as horizontal and vertical ones. So this type of D-Pads can be found even in accessories for the latest generations of game consoles.

— 8-position. A variation of the D-Pad, in which 4 standard directions (2 horizontal, 2 vertical) are supplemented by 4 intermediate — diagonal. In this case, we are usually talking about full-...fledged fixed positions of the manipulator; in other words, to move diagonally, you need to click not on two standard directions, but on one intermediate one. The classic design of this type of D-Pad is a multi-sided button, which is the most suitable option in this case. However, this variety also includes some solutions for 4 separate buttons — provided that these buttons are placed very close, and pressing two at once with one finger is not difficult. Anyway, 8-position manipulators are somewhat more expensive, but more convenient than 4-position ones.

The angle of rotation of the steering wheel in the manipulator-steering wheel (see "Device type"). This parameter is measured over a general range — from one extreme point to another; accordingly, the angle of rotation from the middle position will be half the total. For example, a figure of 180° means that the steering wheel is capable of turning to the right and left by 90°.

Both the general level and the purpose of the steering wheel directly depend on this parameter. Models with a rotation angle of up to 270° are predominantly entry-level and are intended mainly for fans of arcade racing without much emphasis on realism, as well as for children and novice gamers. In more advanced rudders, the steering angle is already 900 °, or even 1080 °. These numbers are taken for a reason — they correspond to the steering wheel ranges in most production cars (900 °), as well as some sports supercars (1080 °). Thus, such characteristics make the use of the steering wheel as realistic as possible — on the other hand, they significantly affect the cost.

The steering wheel rotation range can be adjusted by the steering wheel angle adjustment function (if such a feature is implemented in the game controller). The option is configured either directly in the game, or through the software that controls the operation of the steering wheel.

The material from which the steering wheel itself is made in manipulators of the corresponding type (see "Device type").

Note that the basis of the steering wheel is traditionally plastic. Therefore, this parameter is indicated by the material of the outer surface of the steering wheel: it is with this surface that the user's hands are in contact, it is she who is primarily responsible for the appearance of the device and the general impression of its use.

— Rubber. Rubber coating is relatively inexpensive, while it is quite convenient and practical. So, due to its softness and elasticity, such a surface is pleasant to the touch, at the same time it looks quite authentic — similar materials are often used in steering wheels of real cars. Therefore, it is this option that is most popular nowadays. Of the disadvantages of rubber, one can note only poor scratch resistance, but this is a common feature of many fairly advanced steering wheel materials.

— Plastic. Steering wheel made entirely of plastic; the outer coating may differ somewhat from the base, however, both belong to the same class of materials. The key advantage of this option is low cost; in addition, plastic can be made sufficiently resistant to scratches, scuffs and other damage. On the other hand, the plastic surface is somewhat less comfortable than the same rubber, and it does not always look solid and reliable enough. In addition, smooth plastic tends to slip in the hands...(although embossed protrusions or other similar solutions may be provided to compensate for this disadvantage). Therefore, this material is used less often, mainly in relatively inexpensive steering wheels (although there may be exceptions using high-quality plastic grades).

— Leather. The cover is made of artificial, occasionally — genuine leather. These materials belong to the premium class: they have a stylish appearance, are pleasant to the touch, but they also cost accordingly. However a leather substitute can be both high-class and relatively inexpensive — however, in the latter case, there is no need to talk about durability and durability; natural leather, in turn, is by definition quite expensive. On the other hand, such coatings provide maximum authenticity — to the point that the controller "smells like a real steering wheel, and not like a plastic toy."

— Alcantara. A material also known as "faux suede". In fact, it is a variety of the leather (imitation leather) described above, however, it stands out in a separate category, as it has specific features — primarily a characteristic velvety surface. Thanks to this, this material is pleasant to the touch, while it looks great and at the same time is quite durable and practical; It is worth saying that Alcantara is widely used in the decoration and external tuning of real cars, including luxury cars. At the same time, the cost of such a finish, including for game steering wheels, turns out to be considerable; therefore, only some high-end models are made from Alcantara.

Types of pedals supplied with the manipulator.

This parameter is indicated only in controllers designed for auto racing (in flight simulators, pedals have only one specialization — rudder — and there is no need to specify it additionally). Most of these "racing" controllers are handlebars (see Device type), but pedals can also be produced completely separately. Anyway, the minimum necessary for more or less efficient driving is two pedals, gas and brake. At the same time, for lovers of maximum realism, more expensive three-pedal controllers are being produced that also include a clutch; this complicates the control, but gives many additional features that are not available on two pedals.

The main material(s) used in the design of the manipulator.

Usually, both the body of the device and the control elements — buttons, levers, joystick handle, etc. are made from the material specified in this paragraph. steering wheel ”(see above), the type of coverage is often specified.

Here are the main materials relevant for today:

— Plastic. It is used in the vast majority of modern game controllers — from low-cost to high-end; at the same time, even in inexpensive devices, sufficiently high-quality grades of plastic can be used. In general, this material combines low cost, practicality and ease of design: plastic elements can easily be given complex shapes, as well as any shades and patterns. Of the shortcomings of this option, one can only note a certain tendency to scratches; however, this is a purely aesthetic moment, having almost no practical significance.

— Rubber cover. An additional coating commonly used on plastic devices. Rubber is soft and flexible, and less slippery than a smooth plastic surface. This provides a more comfortable and secure hold in the hands. In addition, scratches are less noticeable on such material. The reverse side of these advantages is a slight increase in the cost and dimensions of the controller (the latter, however, can be compensated by reducing the size of the plastic base).

— Soft touch. A special kind of plastic, a kind of transitional option between traditional smooth pl...astic and rubber. The surface of this material has a special texture, due to which it feels soft to the touch (hence the name), besides, it practically does not slip in the hands. However for a number of reasons, such material has not received much popularity in game controllers.

— Rubberized plastic, rubberized coating. These terms may mean different materials in different models: in some cases it is plastic with a full-fledged rubber coating, in others it is a soft-touch surface. For more on both, see above; and what exactly is at stake — it is worth specifying separately.

— Rubber. The word "rubber" in this case, it is customary to denote individual elements made of this material — primarily buttons and additional inserts. Such elements are usually combined with a body base made of plastic (see above). And rubber is used for additional convenience: fingers do not slip off such buttons as much as with plastic ones, while inserts prevent the controller itself from slipping in your hand.

— Metal. In the case of game controllers, metal is a premium material: it is durable, looks solid, but it is not cheap. And in some types of manipulators — for example, gamepads (see "Device type") — the use of this material is not justified from a practical point of view. As a result, metal is mainly used for individual high-end rudders, joysticks / helms and aircraft instruments, designed both for functionality and for realism in appearance and user experience. At the same time, even if only metal is indicated in the characteristics, the design, usually, still includes individual elements from other materials: for example, the pad on the joystick lever can be made of rubber or plastic, for additional comfort and reliability.

— Aluminium. One of the types of metal described above — with all the characteristic features. Aluminium is often perceived as an advanced and expensive material (in particular, it is widely used in aviation); therefore, sometimes in the characteristics this name is specified for advertising purposes.