Memory rank
The number of ranks provided in the memory bar.
The rank in this case is called one logical module — a chipset with a total capacity of 64 bits. If there is more than one rank, this means that several logical ones are implemented on one physical module, and they use the data transmission channel alternately. A similar design is used in order to achieve large amounts of RAM with a limited number of slots for individual brackets. At the same time, it should be said that for consumer computers, you can not pay much attention to the memory rank — more precisely, peer-to-peer modules are quite enough for them. But for servers and powerful workstations, two-, four- and even eight-rank solutions are produced.
Note that other things being equal, a larger number of ranks allows achieving larger volumes, however, it requires more computing power and increases the load on the system.
Memory speed
The clock frequency of the RAM module.
The higher this indicator, the faster the “RAM” works, other things being equal, the higher its efficiency in games and other resource-intensive applications. On the other hand, a high clock frequency has a corresponding effect on the cost. In addition, in order to use the full capabilities of the memory, the motherboard to which the module is connected must support the appropriate frequency.
The most popular are modules with a frequency of
3200 and
3600 MHz - so to speak, universal workhorses. There are also more modest options - for example
2400,
2666,
2800,
2933,
3000 MHz. And advanced for serious tasks -
3866,
4000,
4800,
5200,
5600 MHz. High-frequency modules
6000,
6400,
6600,
6800,
7000,
7200 MHz and more are also provided.
Clock speed
The amount of information that a memory module can receive or transmit in one second. The speed of the memory and, accordingly, the price of it directly depend on the bandwidth. At the same time, this is a rather specific parameter, which is relevant mainly for high-performance systems — gaming and workstations, servers, etc. If the RAM module is bought for a regular home or office system, you can not pay much attention to bandwidth.
CAS latency
This term refers to the time (more precisely, the number of memory cycles) that passes from the processor's request to read data to granting access to the first of the cells containing the selected data. CAS latency is one of the timings (for more details, see the "Memory Timings Scheme" section, where this parameter is designated as CL) — which means that it affects performance: the lower the CAS, the faster this memory module works. However this is true only for the same clock frequency (for more details, see ibid.).
Now there are memory modules on the market with the following CAS latency values:
9,
10,
11,
12,
13,
14,
15,
16,
17,
18,
19,
20,
21,
22,
24,
30,
32,
36,
38,
40,
42,
46.
Memory timing
Timing is a term that refers to the time it takes to complete an operation. To understand the timing scheme, you need to know that structurally RAM consists of banks (from 2 to 8 per module), each of which, in turn, has rows and columns, like a table; when accessing memory, the bank is selected first, then the row, then the column. The timing scheme shows the time during which the four main operations are performed when working with RAM, and is usually written in four digits in the format CL-Trcd-Trp-Tras, where
CL is the minimum delay between receiving a command to read data and the start of their transfer;
Trcd — the minimum time between the selection of a row and the selection of a column in it;
Trp is the minimum time to close a row, that is, the delay between the signal and the actual closing. Only one bank line can be opened at a time; Before opening the next line, you must close the previous one.
Tras — the minimum time the row is active, in other words, the shortest time after which the row can be commanded to close after it has been opened.
Time in the timing scheme is measured in cycles, so the actual memory performance depends not only on the timing scheme, but also on the clock frequency. For example, 1600 MHz 8-8-8-24 memory will run at the same speed as 800 MHz 4-4-4-12 memory—in either case timings, if expressed in nanoseconds, will be 5-5-5-15.
Voltage
The nominal voltage required for the operation of the memory module. When choosing memory, you must pay attention to the fact that the appropriate voltage is supported by the motherboard.
Lighting
Decorative href="/list/188/pr-29071/">lighting,, usually using LEDs. It does not affect the functionality of the memory module, but it gives it a bright and unusual appearance, which is appreciated by fans of external computer tuning. Of course, in order for this backlighting to be visible, the case must have at least a viewing window, and ideally a completely transparent wall.
It may include synchronization technology. Synchronization itself allows you to “coordinate” the memory backlight with the backlight of other system components — the motherboard, processor, video card, case, keyboard, mouse, etc. Thanks to this coordination, all components can synchronously change color, turn on/off simultaneously, etc. The specific features of such backlighting depend on the synchronization technology used, and each manufacturer usually has its own (Aura Sync for Asus, RGB Fusion for Gigabyte, etc.). The compatibility of components also depends on this: they must all support the same technology. So the easiest way to achieve backlight compatibility is to assemble components from one manufacturer. However, there are many memory modules in the multi compatibility format — that is, capable of working with several backlighting technologies at once. As a rule, such memory is produced by manufacturers that do not have their own backlighting technologies; a specific list of compatible technologies should be clarified separately.
