Comparison Rode Lavalier vs Rode SmartLav+

— Vocal(for karaoke). In accordance with the name, such models are intended primarily for the transmission of the human voice — during singing, artistic reading, etc., when not only speech intelligibility is important, but also shades of intonation. It is these microphones that can be seen on stage during concerts and other similar events, in karaoke equipment, etc. This category also includes models that can also be used as instrumental ones (see below).

— Buttonhole. The name of this type of microphones is due to the traditional method of fastening — on the collar, where the buttonhole is usually located; they have miniature size and the presence of a clip for holding on clothes. Such devices are known primarily as television transmission equipment — they are used by participants in television programs so that they can speak without using their hands with larger microphones. And some devices of this type are actually a “headset blank”, which turns into a full-fledged headset when headphones are connected.

— For a computer. Microphones designed for use with full size PCs. Such microphones usually have a capsule on a long stem, sometimes flexible (see below) and a stand for placement on a table surface. Their main purpose is voice communication using a computer, where the most important thing is not so much the accuracy of the transfer of deta...ils, but the data transfer rate and their small volumes — therefore, the sound quality, usually, is relatively low.

— For a laptop. Like the PC microphones described above, "laptop" models are designed mainly for voice communication and have rather modest characteristics. Their key difference is the focus on use with portable devices, which is expressed primarily in compact size. In addition, for many of these microphones, the connection port also acts as a mount for placement on a laptop case.

— Instrumental. Microphones designed to mimic musical instruments such as saxophones, acoustic guitars (not equipped with pickups), percussion kits, etc. Note that despite the outward resemblance of some models to the vocal ones described above, “purely instrumental” microphones for voice processing are poorly suited, it is not recommended to use them for this purpose.

— Studio. Microphones designed for use in recording studios. Usually, they are designed for recording vocals. Differ in high quality of a sound transmission and the corresponding cost.

— Head. Microphones designed to be worn on the head — like headsets (only in this case there is no earpiece in the design). They are miniature in size and are similar in application to lavaliers (see above), but are located closer to the mouth and do not depend on the speaker's clothing. This allows the use of such models in specific situations where a lavalier microphone is unsuitable — for example, for filming a video with a strong level of extraneous noise.

— For conferences. Microphones intended for use in conference rooms, huddle rooms, grandstands, and similar locations. The design of such models can be different — a capsule on a flexible leg (see below), a disc placed directly on the table, etc. However, anyway, this variety is optimized for speech transmission and is designed for the maximum convenience of the speaker — so that the user is not distracted by choosing the optimal position relative to the microphone and the distance to it.

— For a video camera. Microphones designed, as the name suggests, for use with video cameras, primarily professional ones. Note that technically, any microphone can be connected to the input of the video camera, matching the connectors and main characteristics; however, this category only includes models that are designed to mount directly into a special mount on the camera body.

— For a voice recorder. A specific type of microphone designed exclusively for use with voice recorders. Such equipment, usually, is equipped with its own built-in microphones, but their capabilities may not be enough in some cases; and among high-end professional voice recorders there are devices that do not have a microphone at all. External microphones are usually connected via a 3.5 mm mini-Jack interface or via a proprietary connector (see below), while one of their distinguishing features is the absence of a wire: the plug is mounted directly on the microphone body and plays the role of not only a connector, but also a mount. Of course, miniature sizes are also characteristic of such devices.

— For phone/tablet. This category includes specialized microphones, originally positioned as accessories for smartphones or tablets. Usually, they are similar to the voice recorders described above in the sense that they are attached directly to the body of the device without using additional wires. Their main specificity, compared to the same models for voice recorders, is the connection method — usually a universal connector is used for this, like 30pin / Lightning, microUSB or a proprietary interface (see below for more details).

— For video production. Microphones intended for use in video recording. In fact, this variety includes two subgroups, each with its own specialization. The first is microphones, which can be conditionally called "reporter's". Usually, these include dynamic (see "Type") models with all-round directivity (see below) and good sensitivity. These features allow you to "hear" not only the voice of the reporter, but also the sound background around him; in addition, you do not need to accurately maintain the position of the microphone relative to the face, which is especially useful when interviewing other people. Also, "reporter" models have durable cases and are generally well protected from various troubles (although they are not necessarily completely moisture and shock resistant). The second variety of models for video production is “sound operator”: such microphones can often be seen on film sets mounted on long rods. They, in turn, are usually made unidirectional or bidirectional (for maximum filtering of extraneous sounds), and most often they are condenser types and provide a fairly high quality and reliability of sound transmission.

— Suspended. Microphones designed to be suspended, such as from the ceiling. Such models are intended mainly for choir singing, theatrical performances and other situations in which other types of microphones (standing on a stand, held in the hand or even clinging to the head) are not very convenient.

— Measuring. Measuring microphones are designed to calibrate sound installations. With their help, you can quickly and accurately adjust the loudness for a musical instrument, loudspeaker, sound recording equipment, etc. The key features of measuring microphones are a wide frequency range (20 – 40,000 Hz) and high frequency response stability. The measuring microphone measures the noise level and detects sound anomalies. Properly tuned, with the help of a measuring microphone, the sound installation will fully correspond to the acoustic features of a particular room.

Microphone AC impedance; this parameter is also called "impedance". This is one of the most important characteristics that determines compatibility with the amplifier or other device to which the microphone is connected: if the impedance is not optimal, there may be a loss in signal power. It has its own characteristics, depending on the purpose of a particular model (see above). So, for microphones used with computers, laptops, voice recorders and phones / tablets, the impedance may not be indicated at all — the characteristics of such models are selected in such a way as to ensure normal compatibility with the corresponding devices. But in professional audio equipment, special rules are used for selection; more details can be found in special sources.

Sensitivity describes the signal strength at the output of a microphone when it processes a sound of a certain volume. In this case, sensitivity means the ratio of the output voltage to the sound pressure on the membrane, expressed in decibels. The higher this number, the higher the sensitivity. Note that, as a rule, values in decibels are negative, so we can say this: the closer the number is to zero, the more sensitive the microphone. For example, a -38 dB model outperforms a -54 dB model in this parameter.

It should be borne in mind that high sensitivity in itself does not mean high sound quality - it only allows the device to “hear” a weaker sound. Conversely, low sensitivity is not an unequivocal sign of a bad microphone. The choice for this parameter depends on the specifics of the application: a sensitive device is useful for working with low sounds and in cases where it is necessary to capture the smallest nuances of what is happening, and a “weak” microphone will be convenient at high sound volume or, if necessary, filter out extraneous weak noises. There are models with sensitivity adjustment(and for models with a headphone output , headphone volume control may be provided).

A parameter that describes the relationship between the useful signal level and the noise level produced by the microphone. Note that the actual signal-to-noise ratio varies depending on the sound pressure perceived by the microphone. Therefore, in the characteristics it is customary to indicate the option for a standard situation — at a sound pressure of 94 dB. This allows you to compare different models with each other.

In general, this indicator quite clearly characterizes the quality of work of a particular model, since it takes into account almost all significant extraneous noise that occurs during operation. The greater this ratio, the clearer the sound is, the less distortion it has. Values of 64 – 66 dB are considered quite decent, and high-end microphones provide performance of 72 dB and higher.

Types of connectors provided in the design of the microphone.

Most often, in this paragraph we are talking about the type of connector designed to connect the microphone itself to external audio equipment. Of these interfaces, the most popular nowadays are analogue XLR(including a smaller version of mini-XLR), Jack 6.35 and mini-Jack 3.5 mm, as well as digital USB A, USB-C and Lightning. Also, individual microphones provide their own headphone jack(sometimes Microdot). Here is a more detailed description of each option:

— XLR. A characteristic round plug of a rather large size, usually with an external casing. In microphones, 3-pin XLR plugs are most common, one such plug allows you to transmit one channel of sound; other options are possible — for example, a 4- or even 5-pin connector in a model that supports stereo recording (see "Functions and Capabilities"). Anyway, the main advantage of XLR is the ability to work with a balanced connection. With this connection, most of the interference induced on the cable is extinguished "by itself", without the need for additional filters; this allows fairly long wires to be used with...out sacrificing sound quality. In addition, the XLR connectors provide a tight connection, further improving noise immunity; and for additional security, sockets and plugs of this type are often equipped with locks. The main disadvantage of XLR is its large size; therefore, the main scope of its application remains professional models, where the mentioned advantages far outweigh the disadvantages.

— mini-XLR. A smaller version of the XLR interface described above; has the same technical features and differs only in smaller sizes. The latter makes the mini-XLR more suitable for applications where compactness is important. At the same time, such connectors do not yet have official standardization, and therefore are quite rare.

— mini-Jack 3.5 mm. One of the most popular modern audio connectors. In microphones, however, it is much less common than the same XLR — mainly in compact models, as well as entry-level and inexpensive mid-range solutions. This is due to the fact that the mini-Jack is small in size, but noticeably inferior to XLR in terms of quality and connection reliability, which is why it is poorly suited for professional tasks. It is also worth considering that in modern microphones you can find different versions of the 3.5 mm jack:

• mini-Jack 3.5mm TS. A two-pin connector that allows you to transmit only 1 channel of sound (mono). It is found in fairly advanced microphones, and 3.5 mm jacks of this format are used in basic audio equipment of the appropriate level and specialized devices (like transmitters for lavalier microphones).
• mini-Jack 3.5 mm TRS. Three-pin, the most common type of mini-jack connector. Technically, it can be used for balanced connection of one audio channel (see “XLR” above), but in fact it is more often used either for compatibility reasons (so that the microphone can work normally with three- and four-pin jacks on laptops, phones, etc.), or to transmit a stereo signal (in models with the appropriate functionality — see "Functions and Capabilities").
• mini-Jack 3.5mm TRRS. Four-pin mini-jack plug. It is used mainly in models for smartphones / tablets, camcorders and other equipment — such equipment is often equipped with sockets for exactly 4 connectors, and for optimal compatibility, the same number of contacts is also provided on the microphone. Stereo audio can be transmitted through such an interface, but this capability is not necessarily supported.

Ideally, a microphone with a mini-jack should be connected to a connector that has the same number of pins — otherwise, normal operation is not guaranteed (although exceptions are possible).

— Jack (6.35 mm). Full-size Jack; has almost twice the diameter of the 3.5 mm mini-Jack described above. Poorly suitable for portable equipment, but it provides a fairly tight and reliable connection — although it is somewhat inferior to XLR in this parameter; can also be used for balanced connection (see "XLR"), but in this format it is used relatively rarely. Note that in some microphones, the 6.35 mm interface is provided not as a full-fledged plug, but as an adapter for a 3.5 mm mini-jack installed on the wire. The Jack connector can also have a different number of pins, but in this regard it is not as diverse as the mini-jack: the classic 3 pins (TRS) are the most common, and the 4 pin format (TRRS) is practically never found.

— TA4F. A specialized connector used in audio equipment, and mainly in microphones. Also, this term can mean a connector of a similar design TA3F (with 3 contacts).
The TA4F is fairly small, making it suitable for compact head and lavalier microphones. And thanks to the presence of 4 pins, you can also connect phantom power for condenser microphones through it (however, the use of TA4F is not limited to this type of microphone). Note that this connector is considered professional and is found mainly in the technique of the corresponding level.

— USB. The USB interface is mainly used in computer technology — to connect various peripheral devices. At the same time, among models for PCs and laptops (see "Intended use"), this option is much less common than the mini-Jack 3.5 mm described above, and most microphones with USB are studio ones. This is due to the fact that the signal is transmitted via USB in digital format, which is very convenient when recording to a computer for further processing and mixing (but for voice communication it is more convenient to use a regular microphone input). However, there are other types of microphones with this interface.

— Lightning. A proprietary connector used exclusively in Apple portable devices — iPhone smartphones, iPad tablets and iPod touch players. Accordingly, this connection option is found exclusively in microphones for Apple smartphones, moreover, specially designed for this technique.

— microdot. Balanced jack for coaxial connection to musical instruments and other acoustic/audio equipment. The microDot connector is characterized by the presence of a thread, which ensures a high reliability of the connection. The microDot connection is commonly found in compact microphones mounted on a musical instrument.

— Corporate outlet. This category includes all interfaces not related to those described above. These can be not only their own connectors used by a certain company, but also some standard connection types that are not widely used and are found in specialized technology. However, anyway, when buying such a microphone, you should separately make sure that it is compatible with the device with which you plan to use it.

— Headphone output. Separate headphone output. Most often it looks like a standard mini-Jack 3.5 mm jack — it is this interface that is used in most modern "ears", which gives the user a wide choice. In addition, such an output can be combined with its own volume control.

The remaining features of both the connector itself and its application depend mainly on the type of microphone (see "Microphone"). So, lavalier models, when headphones are connected, turn into headsets; when used in karaoke, headphones make it possible to listen to music better, and when used in a studio, they also allow you to hear your own voice, controlling what is being recorded. Also note that in radio systems (see above), such an output is usually located on the receiver.

This parameter directly affects the freedom of movement and ease of use: the farther the microphone can be taken from the connection point, the more convenient it is, especially when used in large spaces.

The material from which the microphone body is made.

— Plastic. The main advantages of plastic are low cost, light weight and complete insensitivity to corrosion. At the same time, it is considered less reliable than metal, due to its relatively low strength (high-strength varieties of plastics exist, but in the case of microphones, it is usually easier to use metal after all). Therefore, this material is popular mainly among models for which lightness and miniature are important — primarily lapel, head and those that are installed on a video camera(see "Destination"). It is also often found in computer and laptop devices, but plastic microphones for vocals usually belong to the entry-level price category.

— Metal. Metal is more expensive than plastic and has more weight. On the other hand, metal microphones are much stronger and more reliable, besides, a microphone in such a case gives the impression of "solidity" (not least due to massiveness). This option is popular with mid to high end vocal, studio and instrument microphones.

- Receiver. Receiver used on wireless models (see Features/Capabilities). The receiver, in essence, plays the role of a radio adapter: it connects to an amplifier or other audio equipment in the classic wired way and transmits the signal from the microphone to this equipment. For more information about the included receiver, see “Radio System”,

— Transmitter. A transmitter used in systems with a wireless connection (see “Functions/capabilities”), or more precisely, a transmitter designed as a separate device. Miniature microphones (primarily lavalier and headset) have this design, in which the housing dimensions do not allow the transmitter to be built directly into the device: the microphone is connected to an external transmitter using a wire, the latter is usually hung on the belt. The presence of a separate transmitter is usually a sign of a compact microphone; and one of the practical advantages of this design is that the microphone can be detached and connected to other equipment (not necessarily a transmitter).

— Monitor mount. A device for attaching a microphone to a computer monitor. For obvious reasons, it is used only in models for computers (see “Purpose”). This feature is especially useful in cases where there is very little free space on the table where the computer is located, or the microphone cannot be placed on the table in the optimal place. The mount can also be useful for working with a laptop,...although specialized microphones are usually more convenient.

— Holder for stand. A mount in the form of a characteristic round cradle designed to place a microphone on a stand, tripod or other device. Used primarily with vocal and instrumental models (see “Purpose”), it allows you to quickly remove and install the microphone on a stand - which is useful, in particular, during concerts and other public performances. Holders are also sold separately, but buying a model with a complete mount is often more convenient - such a mount is optimally compatible with the microphone and does not require wasting time searching and selecting.

— Anti-shock suspension (“ spider ”). Special shock-absorbing suspension used with studio microphones (see “Purpose”); The slang name "spider" comes from its characteristic shape. The need to use such a suspension is due to the fact that on a regular stand, a microphone can experience various shocks and vibrations (from the operation of equipment nearby, from objects falling on the floor, and even from people’s steps), which create interference in the sound. “Spider” compensates for such shocks and reduces interference to almost zero; At the same time, a complete suspension is more convenient than one purchased separately due to the fact that it is, by definition, compatible with a microphone.

— Pop filter. Such a filter is a plate, usually round, installed in front of the microphone when working with voice - most often during recording; Accordingly, this function is used primarily with studio microphones (see “Purpose”). The protective screen allows sound to pass through well, but it blocks the flow of air that occurs during breathing - thus preventing the appearance of characteristic interference from “exhaling into the microphone.” Another purpose of pop filters is to protect against small splashes of saliva, which can cause corrosion and negatively affect the longevity of the microphone.

— Wind protection. The windscreen most often takes the form of a distinctive “tip,” usually foam, that fits over the microphone; at the same time, in miniature models (for example, head ones, see “Purpose”) the design may be different. However, in any case, the purpose of such devices corresponds to the name: to protect the microphone from exposure to intense air currents that can cause interference. Note that the matter is not limited to wind - a person’s breathing can also become a source of interference if the microphone is located close to the mouth.

— Detachable cable. The ability to detach the cable from the microphone not only makes storage and transportation easier, but also allows you to replace the supplied cable with another if circumstances require it (for example, to connect through a different interface, see above).

- Tripod. A tripod is essentially a portable tripod designed to mount a microphone on a table or other similar surface. This eliminates the need to hold the device in your hand or organize a stand “from scrap materials.” Such tripods are also sold separately, but it is usually more convenient to buy a set; For more details, see "Rack Holder".

- Power adapter. A device that allows you to supply a microphone of a condenser or electret type (see above) with the phantom power required for operation from a regular household 230 V outlet. Thanks to this, it becomes possible to connect the microphone even to tech amplifiers (receivers, players, etc.) that do not have phantom power inputs.

— Case/case. A case is usually called a container made of hard materials, while a cover is usually made of soft materials. The only key difference between them is the degree of protection - the cases are more shock-resistant. But the basic purpose is the same: storing and transporting a microphone in a case/cover is much more convenient than without such a device (in particular, because additional included accessories can usually also be placed inside).

— Charging case. A case is a case made of hard material that simultaneously plays the role of a charger. This feature is very popular in wireless models. The charging case usually has its own battery and the microphone (transmitter) and receiver are charged from this battery; This design provides additional convenience in several ways. Firstly, the case, in fact, also serves as a power bank - an autonomous power source; The capacity of such a “power bank” may vary, but it is usually enough for several full charges. Secondly, the ability to charge small microphones directly in the case reduces the risk of losing them. Thirdly, the charging procedure itself is quite convenient - you just need to connect the cable to the case.

Note that, in addition to the above, manufacturers may include other accessories in the kit - for example, separate clips for attaching lavalier microphones, battery chargers, cleaning wipes, etc.