Comparison Makita TD0101F vs DeWALT DWD115KS

General type of instrument.

Nowadays, several other types of hand tools are also combined into one category with traditional drills, with a similar design and principle of operation: drill drivers, classic screwdrivers, wrenches and electric screwdrivers. Here is a detailed description of each of these varieties:

— Drill. Traditional drills are power tools for drilling holes in various materials. By specialization and “weight category”, such tools range from miniature cordless models to heavy professional diamond drilling units (see “Intended Use”). Anyway, drills are equipped with chucks for installing drills, as well as engines designed for significant resistance during operation. Also note that many of these units have an impact mode, but the drill is still not able to replace a full-fledged rotary hammer (for more details, see "Functions").

— Screwdriver. In fact, it is an electric (or pneumatic) analogue of a manual screwdriver. It is used primarily for tightening and loosening screws, screws and other similar fasteners using bits — interchangeable nozzles, the shape of which imitates various screwdriver tips (straight, cross-shaped, etc.). Accordingly, the standard type of retainer for the nozzle in such a tool is for a bit (see "Chuck Type"). Screwdrivers diffe...r from electric screwdrivers (see below) in higher power, better suitability for long-term work and high loads, as well as larger dimensions and rather significant (in comparison, of course) weight.

— Drill driver. Tools (mainly cordless, see "Power source") that combine the functionality of a drill and a screwdriver. See above for more on both, and these "hybrid" devices are extremely popular these days due to their versatility. Switching between drilling and twisting modes in them is carried out by changing the cartridge, and also, in most models, by adjusting the torque (see below). At the same time, it should be noted that compared to traditional drills, the efficiency of such units when drilling is rather low, they are not intended for high loads, hard materials and large drilling diameters. This is due to the fact that in order to achieve high power, it would be necessary to increase the dimensions and weight, which would significantly complicate the use in the format of a screwdriver.

— Screwdriver. A kind of electric and pneumatic analogues of socket wrenches: tools designed to work with nuts and other similar fasteners (for example, bolts with heads without a slot). Nutrunners are in many ways similar to the screwdrivers described above and differ mainly in the type of cartridge — usually it is a square for sockets of different sizes.

— Screwdriver. An electrical analogue of a conventional manual screwdriver (pneumatic drive is not used in such devices for a number of reasons). Some of these models have a straight body shape (see "Construction") and are very similar in appearance to hand tools; others resemble smaller and lighter screwdrivers (see below). Anyway, electric screwdrivers are intended mainly for work where accuracy and accuracy are more important than high efforts (or where these efforts are simply not required). Thus, the low power of such devices is not so much a disadvantage as a feature. In addition, this feature allows you to use battery power without much difficulty, making the tool as autonomous as possible; in fact, electric screwdrivers with mains operation nowadays are almost never found. And the small size and weight, in turn, contribute to the mentioned accuracy and accuracy.

The total power consumed by a mains-powered electric tool (see "Power Source"). It is considered the main criterion for assessing the overall capabilities of a particular model: more power allows you to achieve more speed and/or torque. However a more correct parameter for such an assessment is useful (working) power, but it is far from always indicated, and tools of the same type with similar power consumption usually do not differ much in terms of working power. In addition, data on power consumption also allows you to estimate the load on the power grid or other power source; in some cases this is unnecessary.

As for specific figures, for different types of tools, the characteristic power values will be different. For example, from 750 to 1000 W is considered a very solid indicator for a screwdriver, while for classic drills this is an average value, among such devices there are options even for 1.5 kW or more. Detailed recommendations on choosing a tool for this parameter can be found in special sources. We only note that it does not always make sense to chase the maximum values high power noticeably affects the dimensions, weight and price of the unit, despite the fact that it is far from always required.

The speed of rotation of the working nozzle provided by the tool.

If a single number is indicated in this paragraph (for example, 1800), it can be either a standard, constant, or maximum rotation speed. This refers to the maximum speed if the tool has more than one speed (see "Number of speeds") and/or a speed controller (see "Functions"). In turn, two or three numbers through an oblique line (for example, 1100/2300/3400) are indicated only for models that have the corresponding number of individual speeds. Each of these numbers indicates the standard (and in the presence of a speed controller — the maximum) number of revolutions at one of the speeds.

Anyway, when choosing a tool by the number of revolutions, it is worth considering both its general type (see "Device") and the specifics of the intended work. Detailed recommendations on this matter are quite extensive, it makes no sense to give them in full here — it is better to turn to special sources. We note only a few general points. So, high -speed drills nowadays are considered to be drills capable of delivering more than 3000 rpm. In general, high speed contributes to productivity, but there is also a downside: increasing the speed (for the same power) reduces torque — accordingly, the efficiency of working with stubborn materials and large diameter nozzles decreases. Therefore, it makes sense to specifically look for a "high-speed" tool only if speed is of key im...portance; it doesn’t hurt to make sure that the model you choose can provide the required efficiency and torque.

The number of beats per minute provided by a tool that supports the corresponding mode.

For more information about this mode, see "Functions", here we note that it can be provided both in drills and in screwdrivers and wrenches (see "Device"), and the meaning of the impact mode in these varieties is somewhat different. Therefore, the speeds differ: many drills are capable of delivering about 48,000 beats / min, or even 64,000 beats / min, while in screwdrivers and wrenches, 3200 beats / min are considered “classics of the genre”, and values above 3500 beats / min are practically do not meet.

The general meaning of this indicator is also directly related to the type. So, among drills, the difference in chiseling speed can be quite large. With these tools, more strokes improve overall productivity and efficiency, while fewer strokes improve accuracy and reduce the risk of damaging delicate materials. In screwdrivers and nutrunners, high speed also contributes to overall efficiency, but for most of these tools, the differences in this indicator are not significant enough to be noticeable in practice.

Torque is the maximum force with which this model is capable of turning the working nozzle.

Higher torque gives more options, it allows you to cope with complex tasks such as drilling in hard materials, unscrewing stuck screws and nuts, etc. On the other hand, a lot of force requires corresponding power — and this, in turn, affects the dimensions , weight and cost of the tool itself, and also puts forward increased power requirements (mains power, battery capacity or pressure / compressor performance). And for some tasks, excessive torque is basically unacceptable, so for maximum versatility, it is desirable to have torque control — and this affects the cost even more. And the more steps, the more optimally you can configure the tool to perform a particular type of work. So the general rule is this: when choosing, it is worth considering the specifics of the planned work, and not chasing the greatest working effort.

Detailed recommendations on choosing the optimal torque for different types of tools (see "Device") can be found in special sources. Here we note that it is of key importance primarily for screwdrivers, although it is also given for other types of tools. At the same time, in the “weakest” models, the maximum working force does not exceed 15 Nm, in the most powerful ones it is more than 150 Nm.

Type of reverse provided in the design of the tool.

The reverse allows you to switch the direction of rotation of the nozzle; see "Functions" for details. It also indicates the type of switch responsible for this function. The varieties of such switches nowadays are very diverse: slider, flag, brush on the engine, on the start button, gyroscopic, on the keyboard toggle switch, and also combined with a flow switch or ratchet mechanism. Here is a detailed description of each of these varieties:

— Crawler. Switch in the form of a slider with two opposite positions. Usually, it moves in the direction "back and forth" relative to the tool chuck — this format is considered the most practical. The sliders are quite simple and at the same time convenient and visual, especially when used in screwdrivers and wrenches: by moving forward (away from you), the direction of rotation is set to twisting, by moving backward (toward yourself), respectively, to unscrewing. However, such devices are widely used in other types of instruments (see "Device") and are generally the most popular option nowadays.

— Combined with the flow switch. Th...e most popular type of reverse in pneumatic tools (see "Power Source"); not found in other models. The flow switch itself is actually a speed controller, most often in the form of a distinctive rotary knob or lever. And if this regulator is combined with a reverse, this means that it can deviate from the neutral position in two directions, and the direction of rotation will depend on which direction the flow switch is shifted.

— Flag. A switch in the form of a flag, usually installed above the start button and thrown to the right and left. One of the advantages of a checkbox is that it is right at your fingertips and can be toggled with almost no unnecessary movement (which is not always available for a slider). On the other hand, this option is mainly suitable for drills, and in screwdrivers and wrenches, the checkbox is not as intuitive as the same slider. And in general, this type of reverse for a number of reasons is much less common.

— Brush (on the engine). Reverse switch installed directly in the tool motor and based on the use of a special movable brush holder. By changing the position of the brushes in the motor with the help of such a mechanism, it is possible to change the direction of its rotation. One of the key advantages of this method is that it allows you to achieve maximum power in any direction of rotation without any special tricks. In addition, such an adjustment has a positive effect on the engine resource. On the other hand, brush switches are quite complex and expensive, and therefore are installed mainly in a powerful professional tool.

— On the start button. Reverse switch combined with start button. Such a combination button is usually made in the form of a "rocker", and the direction of rotation depends on which side of the rocker the user pressed; pressing the same button immediately starts the engine. This design allows you to easily and quickly change the direction of rotation — for this you do not need to be distracted by individual switches, just move your finger slightly and press the other half of the start button. This is especially convenient for screw and wrench drivers, as well as screwdrivers; in fact, most of the models with this type of reverse belong to these types.

— On a keyboard switch. The control method, in many respects similar to the reverse on the start button described above, also uses a rocker switch. The key difference is that in this case the direction switch is made separately from the start button — that is, the user must first select the direction of movement, and then press "start". This option does not have any particular drawbacks, but it also does not differ in convenience, and therefore it is extremely rare.

— Gyroscopic. A rather rare and specific type of reverse, found exclusively in screwdrivers (see "Type"). In fact, there are no external switches in such a tool — instead, a built-in gyroscope is used to track body rotations. Accordingly, to select the direction of movement, you need to rather sharply turn the tool around the longitudinal axis in the appropriate direction and smoothly return it to its original position (speed can be adjusted in the same way — for example, the farther the turn, the higher the speed will be). This control method is very simple and intuitive, but it is rather complicated in technical implementation and requires increased accuracy in handling the tool. That is why gyroscopic reverse is extremely rare nowadays.

— Combined with a ratchet mechanism. Another rather rare option, found exclusively in wrenches — mostly pneumatic, less often battery-powered (see "Power"). The ratchet mechanism, we recall, is responsible for ensuring that the working part of the tool rotates in only one direction. And the reverse is controlled through a mechanical switch, which is directly connected to this mechanism and changes its settings, setting one or another direction of rotation.

The length of the cord attached to the mains powered tool (see "Power Source").

The longer the wire - the farther from the outlet you can use the tool without switching it, the more freedom the user has. On the other hand, an overly long cable creates inconvenience during storage and transportation, and even during operation it can get under your feet (or even your hands). Given this, in most cases, manufacturers equip their products with network cables from 2 to 4 m long. This gives a sufficient degree of freedom without creating inconvenience, and for situations where the length of the wire is not enough, there are extension cords. Of course, even in this range, you can choose a cable for a specific situation: for example, for a city apartment 2 - 2.5 m will be quite enough, but for a construction site it is desirable to have a longer wire.

The total weight of the tool is usually the device itself, without attachments. For battery models (see "Power Source"), usually, the weight is indicated with a standard battery installed; for battery-powered models, the weight can be given both with and without batteries, but in this case this point is not particularly important.

Other things being equal, less weight simplifies work, increases accuracy of movement and allows you to use the tool for longer without tiring. However, note that high power and productivity inevitably increase the mass of the tool; and various tricks to reduce weight increase the price and can reduce reliability. In addition, in some cases, a massive design is more preferable. First of all, this applies to work with a large load — for example, drilling holes of large diameter, or making recesses with impact: a heavy tool is more stable, it is less prone to jerks and shifts due to uneven material, vibration of mechanisms, etc.

It is also worth noting that specific weight values are directly related to the type of tool (see "Device"). Screwdrivers are the lightest — in most of them this figure does not exceed 500 g. Screwdrivers and drill drivers are more "heavy": their average weight is 1.1 – 1.5 kg, although there are many lighter ( 0.6 – 1 kg) and heavier ( 1.6 – 2 kg or more ) mode...ls. And classic drills and wrenches have the greatest weight: such a tool must be quite powerful, so for them 1.6 – 2 kg is an average, 2.1 – 2.5 kg is above average, and many units weigh more than 2, 5 kg.

Two points depend on the type of cartridge: the types of working tools (drills, screwdrivers, etc.) with which this or that model is compatible, and the method of installing / removing them.

— Key. As the name implies, you will need a special key to work with such a cartridge. The mount itself is usually designed for tools with round shanks (mostly drills) and includes three cams that, when clamped, converge towards the centre, clamping the tool installed in the chuck on the axis of rotation. The main disadvantage of this type of cartridge is the need to use a key: it can be lost and the mount becomes useless. In addition, installing and removing a working tool can be quite a long process. However, the key chuck is considered somewhat more reliable than the keyless chuck and more suitable for heavy work.

— Quick release. Similar to the key chuck described above, this type of chuck is designed primarily for drills with round shanks. Its main difference is the absence of a key — you can fix or remove the drill with the help of a hand, without any additional tools. Such chucks are slightly less suitable for work with high loads (for example, in hard materials and/or with large diameter drills), but otherwise they do not lose in any way with the key, and in terms of ease of use they are significantly superior.

— Under the beat. Bits are working...tools used in screwdrivers and screwdrivers (see "Device"). The working side of the bit can have a flat, cruciform or other shape (star, trihedron, etc.), but the shank with which it is fixed in the cartridge is standardly made hexagonal. Accordingly, the bit chuck has a recess for such a shank. Fixation can be carried out mechanically, in the form of a simple latch, or with a magnet; in both cases, the mount is secure enough for safe operation, and the tool can be removed without much effort.

— Morse taper. A cartridge for one of the varieties of the tool cone — the so-called Morse cone. As the name implies, this mount involves a conical shank and a corresponding hole for it (often with an additional groove for the protrusion on the shank — for secure fixation and prevention of rotation). This option is found mainly in drills (see "Device"). Note that the Morse cone is available in several sizes that are incompatible with each other.

— Square. The type of chuck used in impact wrenches. Unlike all other varieties, the working tool for the “square” is not installed inside the cartridge, but is put on it from the outside. Squares can have several standard sizes, but these sizes are the same for both electric and hand tools. In fact, this means that nozzles from manual wrenches can also be used in electric models if the landing size is the same (and if not the same, you can use an adapter, although this is less convenient).

— None (threaded spindle). The absence of a cartridge as such: a thread located directly on the spindle is used to fasten the working nozzles. Almost all models with this feature are powerful professional tools designed for diamond drilling (see "Intended use") — for a number of reasons, it is the threaded spindle that is considered the best way to attach nozzles for such drilling. Note that the thread on the nozzle can be both external and internal; most spindles are compatible with both varieties, but there are exceptions. So this nuance needs to be specified separately.

Note that in some models two types of cartridges can be combined — for example, for a bit and quick-clamping. Usually, for this, the kit provides two different cartridges that can be changed as needed, but there are other options — for example, a spindle into which you can insert both a bit and a drill chuck (key or keyless). Anyway, this makes the tool more versatile and allows you to work with numerous working attachments.