Comparison Novus J-171 vs Novus J-155 A

Standard sizes of fasteners for which the tool is designed. This information is necessary for the correct selection of consumables: each standard dimensions corresponds to certain dimensions of parts, and sometimes also design features. There are a great many standards describing standard sizes; they differ not only in the type of fastener, but also in the geography of application and even by specific manufacturers. Detailed data on various standard sizes can be found in special sources; here we will provide general points on some of the most popular options.

First of all, it is worth saying that the standard dimensions describes only two parameters - thickness and width (for nails - size and width of the head). The length can be different: for example, for the popular staple dimensions 53, the length range can be from 4 to 14 mm, and for 140 - from 6 to 14 mm. At the same time, tools for a certain standard dimensions are not necessarily compatible with all length options. So when assessing compatibility with consumables, you should pay attention not only to this point, but also to the restrictions on the minimum and maximum length of fasteners.

This is what the list of the most popular sizes for rectangular brackets looks like:

- 55. One of the smallest sizes used in modern staplers is 6 mm wide and 1.1 mm thick.
- 90. Another relatively small standard dimensions, it has even a slightly smaller width - 5.8 mm - and a thickness in the...range of 1 - 1.27 mm.
— 57. Staples 10.6 mm wide and 1.2 mm thick.
- 59. The “thin” analogue of dimensions 57, with the same width, provides a thickness of only 0.75 mm.
— 140. Quite rigid staples with a width of 10.6 mm and a thickness of 1.24 mm.
- 114. A slightly enhanced variation of dimensions 57, with increased width and thickness - 10.8 mm and 1.4 - 1.6 mm, respectively.
- 53/53F. Quite wide (11.3 mm) staples, available in both 0.75 mm (53) and 1.25 mm (53F) thicknesses.
— 72. In fact, it’s an analogue of the 53 described above: staples 11.3 mm wide and 0.7 mm thick.
- 54/58. Wide staples 12.8 - 12.9 mm, also available in two thicknesses - 0.75 mm in version 58, 1.25 mm in version 54.

Of the semicircular staples used mainly for fastening cables, the most popular options are:

- S. Relatively small staples with a width of 6.2 mm and a thickness of 1.25.
- L. Larger dimensions - 7.7 mm wide with the same 1.25 mm thickness.

In nails for driving tools, the thickness is indicated by the size, and the width by the largest dimensions of the head. The most popular sizes these days are:

— J. Small fastening nails only 1.2 mm thick with a head width of 2 mm.
— N. Diameter 1.65 mm, cap width 2.8 mm.
- DA. The so-called finishing (finishing) nails are quite large in dimensions: size 1.8 mm, head width 3.5 mm. The head has a characteristic D-shape and, as befits finishing nails, when hammered, it is almost completely recessed into the material.

Regarding pins/studs, it is worth noting that such fasteners are actually nails without heads. Therefore, the main dimensions of such parts is thickness (size), for the most common standard sizes it is as follows:

— 40. Thin pins/studs, only 0.64 mm thick.
— 41. Larger fastener, with a size of 1.2 mm.

Detailed information on choosing a standard dimensions for specific tasks can be found in special sources.

Staple models that the tool is compatible with.

Usually, quite specific options are indicated in this paragraph, so finding compatible consumables is not difficult. The specific dimensions of the fasteners should be specified according to the manufacturer's data — different brands use different markings.

The smallest staple width that the stapler can handle.

The width of the bracket is, roughly speaking, the distance between its legs. Different situations and types of work require different sizes of staples, sometimes quite small. At the same time, staples that are too small will hang out in the store and will not be able to properly fit under the drummer, which is why modern staplers have a minimum size limit. You should pay special attention to it if you plan to work with brackets of small width.

The largest width of staples (see Fastener Type) that the stapler can work with.

The width of the bracket is, roughly speaking, the distance between its legs. Different situations and types of work require different sizes of staples, and sometimes the width must be quite large. However, a staple that is too large simply will not fit into the store, not to mention the fact that the stapler can “shoot” it normally. Therefore, this limit cannot be exceeded, and if you plan to work with brackets, you should pay special attention to the maximum width when choosing.

The smallest length of staples (see Fastener Type) that the stapler can work with.

The length in this case means the length of the leg — in other words, the depth to which the staple clogged "to the stop" penetrates into the material. Small staples do not require much power to drive, but the tool may not be designed for fasteners that are too short due to other parameters — for example, the design of the magazine. Therefore, for many models, this limitation is quite relevant, and in powerful professional models, the minimum length can be quite large — more than 20 mm.

The largest length of staples (see Fastener Type) that the stapler can work with.

The length in this case means the length of the leg — in other words, the depth to which the staple clogged "to the stop" penetrates into the material. This means that working with staples of great length requires not only the appropriate design of the magazine and the feed mechanism — the stapler must also be quite powerful in order to provide the effort necessary for effective clogging. And this, in turn, affects the dimensions, weight and price of the tool. In fact, this means that it does not always make sense to specifically look for a model that can work with long staples — you need to evaluate the specifics of the intended work: often the best choice is a relatively “short”, but at the same time inexpensive and compact tool.

In general, a limit of 10 – 15 mm is typical for entry-level staplers, and in professional models this parameter can exceed 50 mm.

The shortest length of nails (see Fastener Type) that the stapler can handle.

The shorter the fastener, with the same thickness, the less effort is required to drive it, but a nail that is too short simply cannot stand under impact normally. Therefore, for many instruments, this restriction is directly indicated. It is worth paying attention to it first of all if you plan to work with small short nails.

The longest length of nails (see Fastener Type) that the stapler can handle.

With the same thickness, a longer nail requires not only the appropriate space in the magazine and feed mechanism, but also a higher impact energy — otherwise it simply will not work to hammer it “on the head”. This means that the maximum fastener length is directly related to the power and, accordingly, the overall level of the tool. Recall that a powerful professional tool has the appropriate dimensions and weight, moreover, it is often made pneumatic (for more details, see "Type"). Therefore, it makes sense to look for models that are compatible with long nails only if this is critical for the planned work.

The presence of a case or bag in the tool kit.

Such accessories are more convenient than impromptu packaging, they greatly simplify the storage and transportation of both the tool itself and accessories / consumables. At the same time, cases are the most popular in construction staplers — characteristic suitcases made of solid material. Such a suitcase perfectly protects the instrument not only from moisture and dirt, but also from shocks and shocks; it is also often used as the factory packaging in which the tool goes on sale. Bags made of soft material, in turn, are less common: they do not provide such protection against impacts, and they do not resist water / dust as effectively. On the other hand, such packaging itself is less bulky, and when the bag is not needed, it can be rolled up quite compactly.