Power per channel (8Ω)
The nominal sound power output by the amplifier per channel when operating with a load having a dynamic resistance (impedance) of 8 ohms. In our catalog, this parameter is indicated for the mode when all channels of the amplifier work under load (see "Number of channels"); in the presence of unused channels, the rated power may be slightly higher, but this mode cannot be called standard.
Rated power can be simply described as the highest output signal power at which the amplifier is able to work stably for a long time (at least an hour) without negative consequences. These are average figures, because in fact, the audio signal is by definition unstable, and individual level jumps can significantly exceed the rated power. However, it is she who is the main basis for assessing the overall loudness of the sound.
This indicator also determines which speakers can be connected to the amplifier: their rated power should not be lower than that of the amplifier.
According to the laws of electrodynamics, with different dynamic load resistance, the output power of the amplifier will also be different. In modern speakers, the standard values \u200b\u200bare 8, 6, 4 and 2 Ohms, and power levels are indicated for them.
Power per channel (4Ω)
The nominal sound power output by the amplifier per channel when a load with a dynamic resistance (impedance) of 4 ohms is connected to it. See Power per Channel (8Ω) for more information on power rating and its relationship to impedance.
Harmonic distortion
This indicator describes the amount of non-linear distortion introduced by the amplifier into the processed signal. Such distortions are not necessarily perceived as extraneous noise, but they degrade the quality of the sound anyway — for example, they can make it more deaf. It is almost impossible to avoid them, but it can be reduced to levels inaudible to the human ear.
As a result, the harmonic distortion factor (harmonics) is one of the main parameters describing the overall sound quality in Hi-Fi and Hi-End amplifiers. The lower it is, the clearer the sound. Hundredths of a percent are considered a good indicator for modern amplifiers, thousandths and below are excellent. The exceptions are tube and hybrid models, for which rather high harmonic coefficients are allowed; see "Element base" for more details.
Outputs
— Preamplifier (Pre-Amp). The presence in the design of the device of a separate output for the signal from the preamplifier. In the type of amplifiers of the same name (see "Type"), such an output is available by definition and is the main, and sometimes the only one. On integrated models (see ibid.)
, the Pre-Amp output allows you to connect an external power amplifier and use it instead of the internal one. This feature can be useful, for example, to connect a more powerful speaker instead of the original one, or to work in Bi-amping mode. It is worth noting that the Pre-Amp output can also be installed in power amplifiers, playing the role of a "splitter".
— Subwoofer. The presence in the amplifier design of a separate
subwoofer output. Usually, such an output uses an RCA connector (see "Input to the amplifier (Main)"), and the function itself is implemented through a crossover, which selects the low-frequency range in the signal and redirects it to a subwoofer. The "own" output makes it much easier to connect a subwoofer : it does not require any additional equipment, the amplifier itself is enough. This usually provides for the possibility of working with any type of subwoofer — both passive and active; however, in the first case, you will need an additional external amplifier.
— Coaxial S/P-DIF. The presence in the design of the amplifier of the S / P-DIF output of an electr
...ic type, with signal transmission via a coaxial cable. For more information about this interface, see the relevant paragraph in the "Inputs" section.
— Optical. The presence in the design of the amplifier output for transmitting a digital audio signal over a fiber optic cable TOSLINK. For more information about this interface, see the relevant paragraph in the "Inputs" section.
— Jack (6.35 mm). Presence of TRS type outputs in the design of the amplifier. These outputs are jacks for 6.35 mm Jack plugs and may look like the corresponding headphone jack (see below). However, this similarity is misleading: TRS produce sound on the principle of "one channel per plug" (an exception may be information amplifiers). This type of Jack connector is found mainly in high-end professional amplifiers.
— Speakon. An interface used in professional audio equipment to connect acoustics to a power amplifier. It has become widespread in high power equipment, including concert amplifiers (see "Intended Use"), due to its increased reliability and suitability even for working with very powerful audio signals. But in household appliances it is rarely used.
— Control output (IR). The control output allows the amplifier's built-in IR receiver to be used to control other components in the audio system, such as a DVD player in another room, out of range of the remote control, from the remote control. With this scheme of operation, the amplifier actually plays the role of a remote sensor, receiving commands and transmitting them through the control output to another device. Note that the very presence of such inputs and outputs does not guarantee the compatibility of various devices, especially if they are produced by different manufacturers; Sharing details should be clarified in the official documentation.
