Comparison Intex 28210 vs Intex 28202

The working volume of the pool is the amount of water that is standardly contained by the product.

Usually, the working volume is indicated based on the occupancy of the pool at 80% of the maximum capacity. With such a fullness, there will be enough water inside for normal use and at the same time it will not overflow when the next person is immersed in the pool or when waves occur.

The capacity of the pool directly depends on the volume: the larger the tank, the more people will be able to swim in it at the same time. In addition, more capacious models are often also deeper. On the other hand, a large capacity correspondingly affects the cost and puts forward increased requirements for additional equipment: a powerful pump, a performant filter, an efficient drain system, etc. are needed. Accordingly, it does not always make sense to chase large volumes.

In addition, it is worth noting that products with the same volume can differ markedly in size and, moreover, in shape. So in fact, the volume often turns out to be a secondary parameter, and it is easier to choose a pool in terms of length-width-depth.

The type of filter that is standard in the pool.

The filter is one of the most important types of equipment for swimming pools, including frame ones. It is responsible for purifying water from dust, small debris and other contaminants. Considering that modern frame pools are quite spacious, running water through a filter is easier, more convenient and cheaper than changing the whole thing every time it gets dirty. Filters can be like this:

- Sandy. A device with a filter element in the form of a container that holds fine sand of a special composition. When water passes through, sand retains mechanical impurities, including quite small ones. One of the main advantages of sand filters is their high flow Rate; they cope better with large volumes of water than another popular type - cartridge systems (see below). In addition, filters of this type are reusable - if the sand becomes dirty, you do not need to change anything, just organize a backwash. Among the disadvantages of this variety, one can note the relatively low filtration efficiency (including the inability to cope with chemical impurities), as well as the large size. However, in many cases the latter is not a disadvantage - the size of the filter is still small compared to the dimensions of the tank itself, and such a device is located outside the pool, and you can choose the installation location so that the filter does no...t create any inconvenience.

- Cartridge. In accordance with the name, such filters use special cartridges with filter elements in the form of membranes made of polymer material. Cartridges are made disposable; when dirty and worn out, such an element must be replaced. This is associated with additional costs, but consumables are inexpensive, and initially cartridge filters are cheaper than sand filters. Another advantage is their relatively compact size. The operating speed of cartridges is lower than that of sand systems, but such a filter can still be made quite productive even for a fairly large volume of water. Thanks to all this, most modern frame pools are equipped with cartridge devices.

Performance of the pump supplied with the pool (see above).

It refers to the amount of water that the unit can pump per hour. Knowing this amount and the volume of the pool (see above), you can estimate how long it will take to filter it.

Note that manufacturers usually choose the performance of a complete filter, based on the optimal compromise between good speed and low cost, as well as the weight of the unit itself. Therefore, in fact, this parameter may be required mainly in the case of searching for a replacement for the standard filter.

General dimensions of the pool in the unfolded position. In general, this is a fairly obvious parameter; we note only a couple of important points:

— In the largest models, the length or size can exceed 6 m, in the smallest models it does not even reach 2 m.

— It is worth keeping in mind that a frame pool should be filled with water no more than 80%. Accordingly, the maximum depth of such a structure will not exceed 80% of the total height. For example, the category of deep frame pools usually includes products with a height of more than 130 cm - accordingly, the working depth in such models is slightly more than 1 m (130 * 0.8 = 104 cm). And for the younger generation, children's's frame pools are provided, with a side height of up to 60 cm (and a water depth of about 50 cm, respectively)