Power consumption
The power consumed by the construction mixer (see "Device") during operation.
High power provides the device with high performance — such a model can easily cope with complex tasks, such as mixing a large volume of mixture at a time or while working with heavy fillers, such as crushed stone. On the other hand, high power affects the power consumption of the device, its weight, dimensions and cost. It makes little sense to purchase a powerful model if you select a tool for domestic use from time to time.
Rotation speed
The rotation speed of the nozzle or mixing container provided by a plaster mixers.
High rotation speed devices work best with paints, varnishes and glues.
Low rotation speed models do a good job of preparing thick mixtures. Many modern plaster mixers and mixer-drills support the ability to adjust the speed (see "Features"), which allows user to choose the most optimal mode for a particular mixture. Powerful tools especially need a rotation under heavy load support system.
Max. torque
The
higher the torque, the better the tool handles viscous masses, where special force is required to turn the mixing nozzle. It is measured in Newtons per metre (N/m). Note that with an increase in the speed of rotation (see "Number of revolutions"), the torque decreases, and vice versa.
Max. mixing paddle diameter
The vast majority of attachments for construction mixers have a standard size in length, usually 600 mm. But their diameter may differ, its maximum size is limited by the manufacturer, which must be considered when choosing. The indicator depends on the technical characteristics of the tool. The most popular sizes are
120mm,
140mm and
160mm nozzles. The larger the diameter of the auger, the easier it can cope with a large volume of mixed mixture.
Reverse
Type of
reverse provided in the design of the tool.
Reverse allows you to switch the direction of rotation of the nozzle. The type of switch responsible for this function is also indicated here. There are sliders, flags, and on the start button. Here is a detailed description of each of these varieties:
- Slider. The switch is in the form of a slider with two opposite positions. As a rule, it moves in the “back and forth” direction relative to the tool chuck - this format is considered the most practical. The sliders are quite simple and at the same time convenient and visual. That is why they are the most popular option nowadays.
— Flag. A switch in the form of a flag, usually installed above the start button and flipped left and right. One of the advantages of a checkbox is that it is right at hand and can be switched with virtually no unnecessary movements (which is not always possible with a slider).
- On the start button. Reverse switch combined with the start button. Such a combination button is usually made in the form of a “rocker”, and the direction of rotation depends on which side of the rocker the customer pressed; The same press immediately starts the engine. This design allows you to easily and quickly change the direction of rotation - for this you do not need to be distracted by individual switches, just move your finger slightly and press the other half of the start button.
...r>
— There is no reverse. In models without a reverse function, you will have to use special right- and left-handed whisks to mix solutions. Nozzles of the first type are intended for the preparation of thick cement and plaster mixtures, of the second order - for mixing substances with a low degree of viscosity. Mixers with reverse do not have such strict requirements for twisting the spiral in the working nozzle, since the direction of rotation of their shaft can be easily changed.Spindle internal thread
The type of internal thread of the spindle determines the possibility of using one or another nozzle with the tool. Also pay attention to the "Type of cartridge" (see below). Most construction mixers today have a metric thread on the spindle for attaching nozzles:
M12,
M14,
M18,
M20,
M24, but there are also spindles with
⅝” inch internal threads.
Chuck diameter
This parameter determines the possibility of using nozzles of different diameters with the tool. Usually, the larger the diameter of the chuck, the more different nozzles are supported by the plaster mixer.
Max. wood drilling diameter
Refers to models that the user can also use as a conventional drill for drilling wood or metal. The parameter characterizes the largest diameter of holes that can be made using a tool. Here it should be taken into account that some modern mixers allow you to install drills of a much larger diameter than indicated by the manufacturer, and, theoretically, make a larger hole. But the larger the diameter, the higher the resistance of the material and, accordingly, the power of the device should be large. Using the tool on off-design loads is fraught with breakdowns.
Max. steel drilling diameter
The maximum diameter of a hole that can be made with a particular construction mixer or mixer drill when drilling steel. See "Maximum wood drilling diameter.
