The table below shows all the typical error codes that may appear on the information display of Electrolux washing machines.

Error code Decoding
E10 No water supply.
E13 There is a leak in the system.
E20 Error in draining water.
E23 The triac of the electronic board is faulty.
E24 The contacts between the triac and the pump are broken.
E31 Pressostat malfunction.
E32 Damage to the pressure sensor or problem with the filling system.
E33 Problems with pressure sensors and the heating element protective relay.
E34 The pressure switch is faulty or the wiring is broken.
E35 The permissible water level in the tank has been exceeded.
E36 Failure of the heating element's protective relay.
E37 Sensor malfunction.
E38 There is no signal from the pressure switch.
E39 Faulty water overflow sensor.
E3A The door is not completely closed.
E40 Difficulty locking the hatch.
E41 The door is not completely closed.
E42 UBL is faulty.
E43 The triac on the SMA Electrolux has failed.
E44 Sensor failure.
E45 UBL wiring fault.
E50 Problems in the engine chain.
E51 Motor triac malfunction.
E52 There is no contact between the tachogenerator and the electronic unit.
E53 Violation of the control circuit.
E54 Broken contacts or relays.
E55 Wiring problems.
E56 The tachometer or its wiring is broken.
E57 The network voltage is too high: more than 15 Amp.
E58 The problem is in the wiring, motor or electronic module.
E59 The tachogenerator does not give a signal after three seconds from the moment the engine starts.
E5A Problems with the control unit.
E5B There are problems with the wiring or the board.
E5C Control board faulty.
E5D Control board faulty.
E5E The communication between the FCV and the printed circuit board is broken.
E5F Damage to the electronic unit or its wiring.
E60 The display lights up - water heating error.
E62 Water heating too high.
E66 Damage to the heater protective relay.
E68 Overestimation of leakage current.
E71 Error in the operation of the temperature sensor.
E74 The thermistor location is broken.
E82 Selector operation error.
E83 Inability to decipher the selector signal.
E84 The module does not recognize the recirculation pump.
E85 The recirculation pump has failed.
E90 Problems in the communication between the control board and the display module.
E91, E92 Contacts are broken or there is no correspondence between the control board and the interface.
E93 Incorrect configuration.
E94 Non-volatile memory failure.
E95 Contacts are broken.
E96 The information exchanged between the board and connected or not connected elements does not match.
E97 Configuration error.
E98 Communication error between the electronic board and the motor control part.
E99 Incorrect communication between audio and electronics.
E9A There is something wrong with the software between the module and the speaker.
EA1, EA3 DSP or module failure. Faulty wiring or drive belt.
EA2 DSP is not recognized.
EA4, EA5 Problems with the communication circuit, module failure.
EA6 There is no data on reel rotation after 30 seconds.
EB0, EB1 Electronic network disruption.
EB2 Excessive voltage in the network.
EVE, ENE Problems with the electronic module.
EVF, EHF Problems with the block.
EC1 Valve, wiring or block failure.
EC2 The turbidity sensor has failed.
EF1 The drainage system is clogged. Problems with the drain pump.
EF2 Exceeding the detergent limit.
EF3 Damage to the pump or its wiring.
EF4 There is no water.
EF5 The laundry in the drum became clumped and the balance was disrupted.
EN1 Problems with the electrical network or control unit.
EN2 The network voltage has been exceeded.
EN3 Insufficient voltage in the network.
Popular Electrolux washing machines