The table below shows all the typical error codes that may appear on the information display of AEG washing machines.

Error code Decoding
E00 The washing machine does not fill with water.
E01 Drain pump malfunction.
E02 Problems with the drain hose.
E03 The drainage path is faulty.
E11 The washing machine does not fill with water.
E12 The washing machine does not fill with water during the cycle.
E13 The machine is leaking. The aqua-stop worked.
E21 Drain system clogged. The pump is faulty.
E22 Problems with draining water.
E23 The triac of the electronic controller has failed.
E24 Problem with water drainage. Damage to the electrical circuit.
E31 Damage to the water level sensor.
E32 Problem with the temperature sensor. Fast water heating.
E33 Problem with sensors.
E34 The machine does not carry out the washing program.
E35 Pressostat failure.
E36 Problem with water heating.
E37 Damage to the water level sensor.
E38 The machine has problems draining water.
E39 The water overflow sensor has failed.
E3A Damage to the heating element relay.
E41 The hatch door is not closed.
E42 Damage to the hatch locking device.
E43 The washing machine does not start washing.
E44 The problem is in the lock or control board.
E45 The washing machine does not start washing.
E51 The machine does not rotate the drum. The triac has short-circuited.
E52 Tachometer failure. The problem is with the control board.
E53 Electric motor triac circuit malfunction.
E54 The washing machine rotates the drum too slowly or only rotates in one direction.
E55 Open circuit of the electric motor.
E56 The tachogenerator stopped sending signals.
E57 Excess current is more than 15 Amperes or the value of the phase current of the motor exceeds the threshold value of more than 4.5 Amperes.
E58 Excess current.
E59 There is no signal from the tachogenerator.
E5A Overheating of water.
E5B The voltage level has dropped.
E5C There has been a power surge.
E5D, E5E Problem with the control unit.
E5F We need a master.
E61 The machine heats the water too quickly.
E62 The machine overheats the water.
E66 The Ten relay has failed.
E68 Current leak in the washing machine.
E69 The machine does not heat the water.
E71 Problems with the resistance value of the temperature sensor.
E72, E73 The washer dryer heats clothes excessively or does not dry them.
E74 The machine sets an inadequate temperature value when washing.
E82 The washing machine is not running the program that was selected.
E83 The problem is in the module.
E84, E85 The recirculation pump signals are not recognized.
E91, E92 Communication error between boards.
E93 Problem with the board.
E94 Configuration and runtime or program error.
E95 There is no communication between the processor and volatile memory.
E96 The machine does not enter the wash cycle or runs the program incorrectly.
E97 The unit does not enter operating mode or does not operate correctly.
E98 The washing machine does not spin the drum.
E99 The problem is in the module.
E9A The unit emits unusual signals.
E9B, E9C The problem is in the module.
E9D Problems with the machine's internal clock.
E9F Lack of communication between the inverter board and the main control board.
EA1 Incorrect drum positioning.
EA2 The board does not recognize the drum rotation sensor.
EA3 The rotation sensor does not provide fixation of the motor pulley.
EA4 Drum rotation sensor malfunction.
EA5 Damage to the drum rotation sensor thyristor.
EA6 Problems with closing the drum flaps. Drive belt defect. Electronic board error.
EB1 Power supply frequency does not correspond to the required standards.
EB2 The power supply voltage is excessively high and does not meet acceptable standards.
EB3 The voltage in the supply network is too low, much below the permissible standards.
EVE The machine does not turn on.
EBF The unit does not turn on and does not respond in any way to pressing buttons.
EC1 The washing machine does not fill with water.
EC2 Failure of the water turbidity sensor (the error is provided for washing machines equipped with this type of sensor.
EC3 Incorrect operation of the weight sensor.
Ed1 Lack of interaction and exchange of data from two boards: the SMM control board and the main board of the electronic unit.
Ed2 The drying resistor relay is broken.
Ed3 Failure of the second drying resistor relay.
Ed4 The relay that provides power between the washing and drying resistors has failed.
EF1 The drainage system is clogged. Pump failure.
EF2 The washing machine fixes a large amount of foam in the tank.
EF3 The machine suddenly stops working.
EF4 The washing machine does not draw water, although attempts to draw water are heard.
EF5 Drum imbalance and overload of laundry.
EN1 The mains voltage is very high.
EN2 The unit does not turn on.
EN3 The network voltage is very low.
ENE, ENF The machine refuses to work at the beginning or middle of the cycle. Replace the electronic unit.
C0 Pressostat failure.
C1 The washing machine does not fill with water.
C2 Damage to the block
C3 The washing machine does not drain water.
C4 The machine pumps out water very slowly.
C5 Main motor sensor overheating.
C6 Pressostat failure.
C7 Problems with the heating element.
C8 Temperature sensor malfunction.
C9 Engine problems.
CF Volatile memory failure.
CD There is no hatch door lock.
F2 The machine cannot heat water.
F4 The washing machine has problems draining.
F5 The machine cannot fill the tank with water to the required operating level: it fills and drains water at the same time.
F8 The water level in the washing tank of the machine exceeds the permissible level.
F9, F12 The washing machine drum does not rotate.
F13, F14 The machine goes out of control: it may refuse to turn on or does not carry out the given program, stopping in the middle of the cycle.
Popular AEG washing machines