VENTS MA 150 MATP Turbo
 | Compare prices 3 → Size:150 mm Performance:345 m³/h Noise:41 dB Functions:auto blinds |
 |
Close
Configurations VENTS MA 66
Specifications
VENTS 150 MATP Turbo | |||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||
The information in the model description is for reference purposes.
Always clarify the specifications and configuration of the product with the online store manager before purchasing.
Catalog VENTS 2025 - new arrivals, bestsellers, and the most relevant models VENTS.
Always clarify the specifications and configuration of the product with the online store manager before purchasing.
Catalog VENTS 2025 - new arrivals, bestsellers, and the most relevant models VENTS.
Model differences:
- Model 150 MA — motor without ball bearings
- Model 150 MA L — ball bearing motor
- Model 150 MA L Press — Ball bearing motor, 5 blades
- Model 150 MA L Turbo — ball bearing engine, increased power
- Model 150 MA Press — motor without ball bearings, 5 blades
- Model 150 MA Turbo — motor without ball bearings, increased power
- Model 150 MAB — motor without ball bearings, pull cord switch
- Model 150 MAB 12 — motor without ball bearings, pull cord switch, operating voltage 12 V
- Model 150 MAB L — ball bearing motor, pull cord switch
- Model 150 MAB Press — motor without ball bearings, pull cord switch, 5 blades
- Model 150 MABT — motor without ball bearings, pull cord switch, timer
- Model 150 MABTH — motor without ball bearings, pull cord switch, timer, humidity sensor
- Model 150 MAT — motor without ball bearings, timer
- Model 150 MAT L — ball bearing motor, timer
- Model 150 MAT Press — motor without ball bearings, timer, 5 blades
- Model 150 MAT Turbo — motor without ball bearings, timer, increased power
- Model 150 MATH — motor without ball bearings, timer, humidity sensor
- Model 150 MATH L — ball bearing motor, timer, humidity sensor
- Model 150 MATP — motor without ball bearings, timer, motion sensor
Prices VENTS MA 150 MATP Turbo
Series VENTS M (wall and ceiling-mounted)
size: 150 mm, 295 m³/h, noise: 39 dB, pull cord switch, auto blinds, timer, humidity sensor
size: 100 mm, 98 m³/h, noise: 34 dB, pull cord switch, auto blinds, timer, humidity sensor
Model overview based on user reviews
The Extractor Fan VENTS MA is praised for its full automation, featuring a humidity control sensor that activates the fan when humidity levels reach between 60% to 90%. Users appreciate the convenience of not needing to manually operate the fan, although there are concerns about the accuracy of the timer and the noise level, which is attributed to the air movement rather than the mechanism itself. Despite its simple design, the fan is considered pricey, with one user noting a cost of 1800 UAH. Installation may require adjustments, such as repositioning the humidity sensor. While one user experienced a breakdown after seven years, they still recommend the product for its reliability over time. Overall, the VENTS MA is recommended for those seeking an automated solution, though potential buyers should be aware of the noise and cost considerations.
Pros
Cons
2 0 1 1 |
in short, I just wanted a fan that would work on its own, 1800 UAH is kind of too much, especially considering the comments below. If it starts acting up and breaking down, I'll write about it here right away. full automation, now you basically don't need to turn on the fan at all if you've turned your bathroom into a steam room - as soon as it gets very humid, it will start blowing right away. There is a humidity control sensor that works from 60% to 90%, and there's also a timer, which has a minimum setting listed as 2 minutes - checked it with a stopwatch, it was 3:40 - not quite close, haha, so it's probably not very accurate by the humidity sensor either. price - kind of a lot for such a simple design, even with a humidity sensor, and I don't understand why, but it's quite noisy, it's the air, not the mechanism, and the last thing - the internal layout - my wires connect to the ventilation to the left of the opening - had to rearrange it a bit inside (moved the humidity sensor under the grate to another place) but that's more of a question for me  Vadim: use VENTS MA less than month |
I won’t say it’s bad, it worked for 7 years without problems, then the impeller mount fell apart. The big problem is to find a separate impeller, probably only print it on a 3D printer. I have a model without a humidity sensor, there were no problems with the blinds. I can confidently recommend this product. Works great. Noisy |
2 out of 4 user review(s) shown
2 more user review(s)
We recommend
