Comparison Krauff 26-178-025 0.75 L vs Tramp TRC-031 0.75 L

The type of main cover provided in a thermos. The main cover in this case is a device that directly covers the working volume of the vessel; an additional cap can be installed on top of it, which often also plays the role of a cup. In modern thermoses there are the following types of main lids: screw-on (screw), valve, cover, hinged cover, drinking cover, pump (pump), stopper. Here are the features of each of them.

- Screws on (screw). Solid (without holes) screw-on cover, secured with a thread. Such lids are very simple and at the same time reliable, but you cannot drink or drain the contents through the classic screw - you have to remove it completely. There is also a more advanced design that allows you to drain the contents without removing the screw - just partially unscrew it; however, this is a rather specific option that is not used often. Be that as it may, twists are found mainly among classic and food thermoses (see “Type”), for which the mentioned nuances are not decisive.

- Valve. A cover (most often threaded) equipped with a valve through which the liquid contents of the thermos can freely flow. Such lids are more complex and more expensive than “blind” screws (see above), but to acce...ss the contents you don’t need to unscrew the screw every time, just open the valve. This not only provides additional convenience, but also reduces heat loss. Thanks to these advantages, valves are extremely popular in classic thermos flasks; they are also often used in thermal mugs (see “Type”). The disadvantages of this option include the fact that the valve opening is usually made quite narrow and is easily clogged with impurities (for example, tea leaves or coffee grounds). Therefore, the valve can only be used for liquids without such impurities (this also applies to food thermoses, which can also be equipped with valves). However, there are models with two different valves included, for drinks of different consistencies and aromas.

- Lid. Lids in this case are devices that do not have threads (unlike the screws described above) and are held in place solely by friction or a latch. The design of the lids can be different: some cover the neck from the outside, others are pressed inward when closing; There are also more specific options. In any case, the lids are easy to remove and put back on, but they are not very reliable - for example, it is not recommended to turn such vessels over. Therefore, this option is found mainly in thermal mugs and thermoses for food (see “Type”), for which the mentioned disadvantages are not critical.

— Hinged cover. A variation of the lids described above, which, when opened, is not removed entirely, but is folded to the side on a special mount. Thanks to this, the likelihood of loss is reduced: in fact, you can only lose the cover along with the thermos itself; and a latch, spring, or other similar device is usually provided to hold the cover in the open position. On the other hand, mount somewhat affects the price and dimensions of the vessel. This drawback is least critical for flasks and mugs (see “Type”), and it is among these types that hinged lids are most often found.

— Cover-drinker. Lid (regular or threaded), complemented by a special hole for drinking. This design allows you to drink from the vessel without removing the cover; and during “non-working” hours the hole is covered with a flap or other similar device. Drinking lids are extremely popular in thermal mugs and auto mugs (see “Type”): they allow you to drink from the mug comfortably while at the same time minimizing heat loss and the likelihood of spilling the contents.

— Pump (pump). Lid (classic or threaded) with built-in pump. Most often, this pump is activated by a special button: when you press this button, a portion of liquid comes out of the spout, and the thermos does not need to be tilted. However, such devices are quite complex and cumbersome, so it makes sense to use them only in thermos jugs (see “Type”): the size and weight of the pump is small compared to the dimensions of the jug itself, and tilting such a thermos can be difficult - it’s easier to use a pump.

- Cork. A classic stopper that fits tightly into the neck of a thermos and is held in it without threads or other similar devices. Corks differ from the lids described above in their greater thickness, and also in that they are inserted into the neck from the inside (while the cover can cover the vessel from the outside). Plugs are very easy to use, but have low reliability, which decreases even more as they wear out. As a result, this option has practically fallen out of use.

The main property of a thermos is to maintain the temperature of the liquid poured into it. Accordingly, the key parameter of efficiency is not so much the case material or some of its heat-insulating marketing chips, but the value of the water temperature after a certain period of time. So manufacturers, confident in the quality of their products, are happy to share their achievements. The temperature value after 6 hours shows how many degrees the boiling water poured into the thermos (98 °C) will cool down at an ambient temperature of about 20 °. And values of more than 80 ° can be considered very worthy.

The main property of a thermos is to maintain the temperature of the liquid poured into it. Accordingly, the key parameter of efficiency is not so much the case material or some of its heat-insulating marketing chips, but the value of the water temperature after a certain period of time. So manufacturers, confident in the quality of their products, are happy to share their achievements. The temperature value after 12 hours shows how many degrees the boiling water poured into the thermos will cool (98 ° C) at an ambient temperature of about 20 °.

The main property of a thermos is to maintain the temperature of the liquid poured into it. Accordingly, the key parameter of efficiency is not so much the case material or some of its heat-insulating marketing chips, but the value of the water temperature after a certain period of time. So manufacturers, confident in the quality of their products, are happy to share their achievements. The temperature value after 24 hours shows how many degrees the boiling water poured into the thermos will cool (98 °C) at an ambient temperature of about 20 °. And with values of more than 50 °, a thermos can be considered one that keeps the temperature for a long time.