Comparison Eken H8R vs ATRIX ProAction A30

The degree of dust and water protection of the protective case supplied with the camera.

Protected case will save your camera from dust, water, temperature changes, shocks, etc. The specific degree of protection is indicated according to the international IP (Ingress Protection Rating) system, according to which each device is assigned a code of the form IPXX, where X is replaced by specific numbers. The first of them characterizes the protection against the penetration of foreign objects (from 0 to 6, where 0 is no protection). Usually, in boxes for action cameras, this indicator does not go below 5, because otherwise the container would have too large gaps, and its use simply would not make sense. Level 5 provides dust resistance — dust can get inside the case, but in small quantities that do not affect the device inside. Level 6 corresponds to complete imperviousness to dust.

The second digit is protection against liquid ingress (from 0 to 8, where 0 is no protection). Usually, the minimum level of protection against water is 6.

6 — protection against short-term immersion (for example, falling into a sea wave);
7 — protection against temporary immersion under water (up to 30 minutes) to a shallow depth (up to 1 metre), without continuous operation in immersed mode;
8 — protection against immersion to a depth of more than 1 metre for a time of more than 30 m, with the possibility of continu...ous operation underwater. The specific level of protection of level 8 can be quite impressive — up to the possibility of diving to several tens of metres.

Note that protective cases for action cameras can be sold separately. Therefore, if the capabilities of the complete container do not suit you, there may be a more secure case on the market. On the other hand, in general, it is still more convenient to buy such an accessory immediately with a camera — so as not to waste time and effort on choosing the right protective case.

Camera ability for recording WVGA (480p) video.

The most popular resolution options provided by this standard are 640x480 and 848x480; there may be other options, for example, 736x480 or 720x576, but the resolution of such a video is very low by modern standards.

Another important parameter indicated in the specs of the video is the frame rate. The higher it is, the smoother the picture looks, and the less moving objects are blurred in the frame. Accordingly, the higher the frame rate, the better the dynamic scenes will look on the video. A value of 120 fps or more usually indicates that the camera can shoot video in slow-motion format (although it should be specified separately). At the same time, many models with high fps allow you to set a lower frame rate than stated in the specifications — for example, a camera for 120 fps can also support 30 and 60 fps. This feature is useful in cases where you need to save memory — the higher the frame rate, the more space the video takes (at the same resolution), and by reducing the number of frames per second, you can fit more material in the same amount of memory.

The ability of the camera to shoot QuadHD video.

This standard includes an extensive set of resolutions — from 1440 to 3456 pixels horizontally and from 1440 to 2160 pixels vertically, with almost two dozen intermediate options. It is a rather specific transitional option between the relatively inexpensive FullHD 1080p and the demanding UltraHD 4K, allowing you to shoot higher resolution video than 1080p without significantly increasing the cost of equipment. Note that pure QuadHD resolutions are rare in TVs and monitors, but modern technologies make it possible to comfortably watch videos of this format on any high-resolution screen.

Another important parameter given in this paragraph is the frame rate. The higher it is, the smoother the movement in the frame will be, and the details in dynamic scenes will be visible clearly. For example, a filming speed of 25 fps or 30 fps approximates the standard frame rate in film and television; such an image is quite viewable, but fast-moving objects in the frame will look blurry. With an increase in speed to 60 fps, this effect becomes almost imperceptible. The highest QuadHD frame rate found in modern action cameras is 120 fps; this frequency is used when shooting slow-motion video (as well as models with a frequency of 100 fps)...because at a normal playback speed, 60 fps is enough.

Frame rate supported by the camera when shooting in slow motion.

In general, such shooting is called “high-speed” because it is carried out at an increased frame rate (more than 60 fps). As a result, when played back at normal speed (60 fps and below), the video looks slow hence the name. This kind of slow-motion can be used just for fun, as an artistic technique, and even for scientific purposes — to capture movement that is too fast for the human eye. In any case, the higher the slow-mo frame rate, the more you can slow down the video and the more advanced the camera is in this regard. On the other hand, the higher the frame rate, the more performant the graphics part should be; and this, in turn, affects the price of the device, sometimes quite noticeably.

We also note that slow-mo shooting may be available only at certain resolutions, not always at maximum. These points can be directly specified in the specs of the action camera.

The number of megapixels in the action camera sensor, in other words, the resolution of this sensor(1 megapixel is 1 million photosensitive points).

There is an opinion that the higher the resolution, the better the image quality. It is true from the point of view that manufacturers are trying to install high-resolution sensors in advanced cameras. At the same time, there are no strict dependencies here, and from the technical point of view, the number of megapixels determines only the maximum image resolution that can be captured using this sensor. The quality of this picture will depend both on several features of the sensor itself (size, type, special design solutions), and the specs of the camera. So when choosing, you should focus not so much on the resolution of the image sensor, but on the general class of the camera and reviews with examples of footage.

The maximum resolution at which the action camera can take photos. Specified in pixels horizontally and vertically.

This parameter is directly related to the resolution of the image sensor(see above): the total number of pixels in the photo, usually, corresponds to the number of pixels in the sensor. For example, a photo resolution of 4608x3456 corresponds to a sensor of 15925248 pixels, or approximately 16 megapixels. If the number of pixels in the photo is greater than the claimed resolution of the sensor, then the manufacturer uses software tricks that allow you to improve the photo resolution to a higher one than originally. This reduces the cost of devices but also affects the quality of images.

Theoretically, high-resolution images can provide good detail, but in fact, much depends on the specs of the sensor (primarily physical size) and image processing features.

— Diagonal. The larger the screen, the more convenient it is to watch (and also to control if the display is touch-sensitive). On the other hand, the diagonal of the built-in display directly affects the size of the case, and action cameras should be quite compact. Thus, there are practically no screens larger than 2.5" in modern action cameras.

— Resolution. Theoretically, the higher the resolution, the clearer and better image the screen produces. On the other hand, displays in action cameras are designed mainly for menu operation and footage preview — and for these purposes, especially high resolutions are not needed. For models with two screens, the rear display is considered the main display.

— Touch screen. Display equipped with a sensor and responsive to touch like in smartphones/tablets. Control through such a display is simpler and more intuitive than using buttons, rotary knobs, etc. On the other hand, for more or less convenient control, the touch screen must be quite large, which affects the dimensions of the entire camera.

— Front screen. The presence in the camera of a screen mounted on the front panel, next to the lens. Other displays may not be present at all; in such cases, the diagonal, resolution and other parameters are given for the front screen.

It is worth noting that most often the simplest black...-and-white displays are installed on the front panel, suitable only for text and basic graphic information. However, even on such a screen, you can display a wide variety of service data: the current mode of operation (photo, video, standby), the resolution used, the shooting time, the amount of free space on the drive, etc. But more advanced displays are not used as front displays: a full-colour screen is needed only for taking a selfie, and for this you can use a remote display with a remote control(see "Control") or a smartphone connected to the camera.

Speaker or speakers installed directly in the camera body. This function is mainly intended to allow you to view footage with sound without connecting headphones or external speakers. However the built-in speakers do not have decent volume or general sound quality — nevertheless, they allow you to determine what the camera “heard” as a whole, whether sound recording was turned on, whether individual ambient sounds got into the recording, etc.

— Protective case. A special container that provides additional protection against dust, moisture, shock, extreme temperatures and other similar “troubles”. The specific degree of protection in each case must be specified separately. In order not to interfere with the shooting, the box is made of transparent materials. In addition, we note that some cameras can only be mounted on mounts in a protective case (or in a mounting frame — see below), since the camera body may not have mounts for this.

— Curved mount(helmet). A mount designed to mount the camera on a helmet or other curved surface. The design of such a mount is based on a curved platform with an adhesive layer or hook-and-loop, the shape of which approximately corresponds to the shape of the surface of the helmet. Such a fixture can provide a more secure hold than the classic flat platform (see below).

— Flat mount. One of the basic and simplest mounts used to fix an action camera on almost any uniform surface: snowboard, skateboard, car hood, etc. It is a small flat platform, on one side of which the camera is attached, while the other is fixed on the desired surface (using hook-and-loop, special glue, etc.). Note that flat mounts are often used for mounting on a helmet. However, there is a separate type of mount for this, with a curved platform (see above).

— 3-axis mount. It differs from other types of mounting in the presence of three movable nodes that allow you to rotate the camera at an angle of up to 90 degrees in three axes. This allows you to choose the most interesting or successful shooting angle — on the side of the helmet, for example. Such options are usually compatible with many other mounts, so they can be used in conjunction with a handlebar, curved mount, etc.

— Bicycle/moto handlebar. Mount for installing the camera on a small pipe, such as the handlebars of a bicycle or motorcycle. Usually, it looks like a clamp, and the size of the fastening can be adjusted within a fairly wide range, adjusting it to pipes of different diameters.

— Suction cup(on glass). Camera mount, fixed in the right place with a suction cup. Allows you to install the device on flat and slightly curved surfaces. At the same time, note that such fasteners are not held as securely as flat or curved ones (see the relevant paragraphs). On the other hand, the suction cup is easy to attach and remove and leaves no marks. Therefore, mounts of this type are mainly used for installation on car glass when the camera works as a DVR.

— Clamp (clip). The clip-pin mount is quite versatile since it allows you to hang the camera on almost any suitable piece of equipment (backpack strap, unloading belt, belt, etc.). But at the same time, it is not very suitable for extreme shooting due to the relatively low reliability.

— Head mount. A device for fixing the camera on the head — usually on the forehead, like a headlamp. In addition to being hands-free, this placement has another advantage: the camera lens faces the same direction as the user. In this case, the mount itself is usually a system of elastic straps and is designed to be worn directly on the head, in contrast to the curved platform for the helmet. However, in some models, the possibility of putting on a helmet is also allowed.

— Chest mount. This mount is a system of elastic straps that allows you to fix the camera on the user's chest, shooting a little lower than the "eyeball". Like the head mount (see above), it easily adapts to the desired size.

— Mounting frame. A device designed to mount the camera on various mounts — helmet-mounted, on the handlebar, etc. The camera body itself often does not have mounts for such fixing, which is why you have to use additional equipment. Note that a similar function is often performed by a protective case(see above); the mounting frame, in contrast, provides almost no protection. However, in the frame, the camera body remains as open as possible. This provides additional features — in particular, it allows you to connect various cables and effectively use the built-in microphone, which is not possible with many protective cases.

— Monopod(selfie stick). It is a rod, usually folding, and sometimes adjustable in length; on one end of the rod is a mount for the camera and on the other — a handle for holding in your hand. By the name, such a monopod is intended mainly for filming itself — thanks to the length of the rod, the camera can be held at a convenient distance for this. However, other applications are also possible: for example, with the help of a monopod, you can “look” quite far over the edge of a cliff or around a corner. The main disadvantage of such a device is that one hand is constantly busy.

In addition to those mentioned above, other types of mounts may be included in the delivery package — for example, for musical instruments (for a guitar neck, a drum kit bar, etc.), for a surfboard, etc.