Comparison Audio-Technica AT-LP60X-USB vs Audio-Technica AT-LP60-USB

Model of the pickup (cartridge) supplied with the player. The pickup is one of the most important parts of any vinyl player, the quality of the received sound largely depends on its quality. Knowing the name of the model, you can find detailed data on it and determine how satisfied you are with this particular cartridge.

The force of pressing the needle on the plate, which the complete pickup (cartridge) is designed for.

This force depends on the rigidity (compliance) of the needle: the greater the clamping force, the harder the cartridge, respectively, the less pliable it is. It is also believed that less pressing force wears out the record less, but it cannot be said that "light" cartridges are definitely better — there are many other nuances. So in fact, information about the pressing force of a complete pickup is needed mainly in case of its replacement. Usually, the pressing force provided by the arm of the turntable is regulated within these limits, so the new cartridge must also be rated for the same values of downforce — otherwise there is a chance that the turntable will not be able to correctly align.

The weight of the pickup (cartridge) supplied with the turntable.

The weight of the cartridge determines the characteristics of balancing the tonearm to set the optimal tracking force. However, pickups in set are usually optimally compatible with the corresponding tonearms, so there are no problems with adjusting the turntable. But when buying a replacement cartridge, you should pay attention to this parameter: it is advisable that the new cartridge does not differ too much in weight from the old one, otherwise the tonearm adjustment range may not be enough for the correct balance.

An external power supply is called a power supply unit (PSU) placed outside the player's case; such a unit can be connected to the outlet with a wire or plugged directly into it using its own plug. The point of this arrangement is to minimize possible interference from the power supply electronics by removing it to the maximum distance from the circuits through which the signal passes. Therefore, an external power supply is considered the best option for audiophile class acoustics.

— Tempo adjustment. The presence in the player of an electronic module that allows you to change the tone of the sound being played, in other words, to make it higher or lower by a certain interval, in other words, change the playback speed. This feature is also known as a "pitch controller". It is relevant primarily for DJ "turntables", as it allows you to mix tracks recorded in different keys. Some home players also have a tempo control, but its capabilities are much more modest, and a real need for such a function rarely arises.

— Adjustable counterweight. The ability to adjust the position of the counterweight mounted on the opposite end of the tonearm from the cartridge. This allows you to change the balance of the tonearm by adjusting the downforce (see above); the presence of an adjustable counterweight is highly desirable if you plan to use "non-native" pickups with the player.

— Anti -skating. The presence of an anti-skating system in the design of the tonearm. The peculiarities of the work of the vinyl player are such that during playback there is an additional force that presses the needle against the inside of the groove. This results in an imbalance in the sound of the stereo channels and uneven groove wear. To compensate for this phenomenon, anti-skating is used — a system that “pulls” the tonearm in the opposite direction, towar...ds the outer edge of the record. Anti-skating may be based on counterweights, springs, magnets, or other devices, but anyway, this function is considered highly desirable for modern turntables. However, it is not available everywhere: for example, in low-cost models, anti-skating may not be provided to reduce the cost, and in top-end devices it may be present, but not indicated in the specifications.

— Reverse playback. The reverse function allows you to play the record in reverse, playing the sound backwards. This feature is unlikely to be needed by audiophiles, but it is very much appreciated by DJs, as it expands the arsenal of available sound effects. Usually, direct drive is required for reverse (see above), although there are exceptions.

— Hitchhiking. A system that automatically stops the disc and raises the arm when the record has finished playing. Due to this, additional wear of the needle due to movement along the plate "idle" is prevented. However, in some situations (for example, when playing several records in a row), hitchhiking is inconvenient, so it can be turned off.

— Autoplay. The presence in the player of automatic playback. In such models, the user does not need to manually move the tonearm. In fact, it is enough to install the record, press the button — and the disc will start to rotate, the tonearm will lower itself to the desired position, and after the end of playback, the record will stop, the tonearm will rise (due to hitchhiking, see above) and return to its original position. Such systems make the player as convenient as possible, but they significantly affect its cost, and also (like any additional electronics) are a potential source of interference.

— Built-in acoustics. The presence in the player of its own speaker system, consisting of speakers and a power amplifier. This equipment allows you to listen to records without the use of external equipment; in fact, models with acoustics are stand-alone music centers, except that they work not on cassettes / discs / flash drives, but on vinyl discs. At the same time, the characteristics of the built-in amplifiers and loudspeakers are generally noticeably more modest than those of external ones, and additional electronics in the player's case can distort the signal. Therefore, it makes sense to purchase models with built-in acoustics if purity and high sound quality are not critical — for example, for listening to old records.

— Speed 78 rpm. The ability to operate the player at a speed of 78 revolutions per minute. To date, such records are almost never produced, but they were very popular until the 60s of the XX century. Therefore, to listen to vintage audio recordings, you will need a turntable with support for this speed. Note that 78 rpm operation may require additional equipment (such as a belt pulley or a special pickup).

— Write to media. The ability to connect an external media to the player and record the reproduced sound on it in digital form. Usually, we are talking about USB-drives (such as flash drives); accordingly, a USB Type A port is provided for their connection. However, other types of media, such as memory cards, may be supported. Recording directly to media is faster than digitizing via a computer (see "USB port (type B)" above), but the sound is recorded "as is" in this case, without the possibility of quality enhancement and noise filtering.

— Installation of the second tonearm. Possibility of installing an additional tonearm on the player, which can differ markedly from the main one both in its own features and in the characteristics of the pickup. This possibility is justified if the player is planned to be used in different modes that cannot be covered by a single pickup. For example, you can install an inexpensive pickup on the second tonearm, which is not a pity to “kill” on old worn records, or a 78 rpm cartridge for vintage recordings. Note that in some models there may be more than one additional tonearms.

— Pendulum alignment. Automatic turntable leveling system based on a pendulum (suspension). This feature is found exclusively in premium class models, designed for the highest mechanical precision. In such models, the player itself is installed on a special stand on the floor, and a massive (several tens of kilograms) pendulum is suspended from its lower part. While the pendulum hangs strictly vertically, the player's disc is in a strictly horizontal position; and due to the large mass, the suspension practically does not deviate from the vertical with small vibrations of the floor (for example, from people walking nearby). This feature is designed primarily for sophisticated audiophiles who want to get the most accurate and reliable sound.

The range of frequencies that the player is capable of outputting when using a standard pickup.

The wider the frequency range, the more complete the sound picture will be, the less low and/or high frequencies will remain behind the scenes. However, from a practical point of view, it does not make sense to expand the range beyond the values \u200b\u200bof 16 – 22000 Hz — it is within these limits that the human ear hears the sound (and even then not everyone). In high-end audio equipment, including turntables, there are more extensive ranges; however, such characteristics are a kind of “side effect” of high-end technology that manufacturers use for advertising purposes.

In addition, we note that an extensive frequency range is not yet a guarantee of high-quality sound: the sound picture depends on many other parameters, from the amplitude-frequency response to extraneous interference.

Rated power consumed by the player during normal operation.

Modern turntables are very economical: most models, even those equipped with built-in acoustics (see "Features"), the power consumption does not exceed 15 W, and there is no need to talk about any serious impact on congestion in the electrical networks (as well as electricity bills). The exception is some premium-class devices, in which the weight of the platter (see below) reaches several tens of kilograms, and the corresponding engine power is required to rotate such a mass.

The material used for the base of the turntable — or, as it is also called, the support table.

The base is actually the body of the player, the tonearm, platter and drive are mounted on top of it. Note that a set of modern turntables can include both a base and a base with a tonearm, and the most extensive option, called complete set, also includes a pickup. As for the materials for the base, they must meet specific requirements — in particular, be quite heavy in order to reduce extraneous vibrations transmitted to the device. Here are the most common materials:

— Plastic. The main and, in the case of vinyl players, practically the only advantage of plastic is its ease of production and, accordingly, low cost. At the same time, the performance characteristics of such material are quite modest, so it is the prerogative of inexpensive "turntables".

— Acrylic. Technically, acrylic is a type of the plastic described above, but in general, this material is much more advanced in terms of performance, while it is relatively inexpensive and can have an original appearance (in particular, become transparent). Acrylic tables are typical for fairly solid models.

— Metal. Metal bases are massive and highly durable, however..., they are not cheap, and therefore are found mainly in premium turntables.

— MDF / fiberboard. Fiberboards, in addition to good acoustic characteristics, are notable for their pleasant appearance, especially suitable for retro-style devices. Such material can be used in quite expensive models.

— Carbon. High-quality material, characterized by high strength and quite stylish appearance. On the other hand, it has a relatively low weight, which has to be compensated for by the significant thickness of such bases, and this affects the cost (despite the fact that the material itself is not cheap anyway). Therefore, carbon has not received much distribution.

— Granite. Natural granite is very heavy and dampens vibrations well, but it is also a very expensive material. It is used extremely rarely, mainly in premium players, not only for the sake of practical characteristics, but also to emphasize the level of the device.

The diameter of the disc on which the record is placed.

The standard diameter of a 33 rpm vinyl record is 12", or 300 mm. The diameter of the platter can differ from this value in one direction or the other; in normal listening to music this does not play a special role, but for a DJ " turntables, it is desirable that the disk be wider — due to this, it is more convenient to control the rotation.