Multi tool: 5 models

Sturm MF5630C

Producer: "Sturm GmbH", Germany

The Sturm multitool certainly belongs to the household category. But thanks to the German roots of the brand, the manufacturer manages to create a reliable low-cost power tool. Main technical characteristics of the oscillating tool Sturm MF5630C:

• power consumption 300 W;
• oscillation frequency from 15,000 to 22,000 counts/min;
• swing angle 3°;
• mains power;
• weight 1.25 kg.

One of the most significant advantages of the device is the price. Indeed, it is very tempting to purchase a multifunctional tool at the price of a simple drill. Yes, and the technical characteristics of the device do not cause concern: sufficient power, a decent frequency of oscillation, low weight, everything is on the level.

There is even a speed controller. You can adapt the tool to different materials and working conditions without turning off the engine. Sturm MF5630C comes in a case, which is very convenient, since the tool is used with a set of nozzles that need to be stored somewhere.

At the same time, netizens note that with continuous operation for more than 3 minutes, the body starts to heat up, and after 5 minutes of intense work, it is very inconvenient to hold the tool without protective gloves. At first glance, the manufacturer provides good air cooling, but judging by user reviews, it is not enough. Perhaps the reason for the rapid overheating is the quality of the lubricant used or the soldering of the contacts of the internal wiring.

Externally, the build quality is not satisfactory, but users also note that the Sturm oscillating tool vibrates quite strongly when used.

The model is suitable for occasional use in an apartment or garage. The tool will successfully cope with simple tasks. The multitool will relieve the user of the need to purchase and keep at home a whole arsenal of power tools. But if you are going to do a major overhaul or use the tool regularly, you should also take a closer look at other contenders in our review.

Black&Decker MT300KA Price from 3 026 up to 5 892 ₴ →

Producer: "Stanley Black&Decker", USA

Stanley Black & Decker engineers, in the manufacture of their equipment, usually, profess the principle of the universality of the use of power tools. This approach has ensured their series of oscillating instrument rather high popularity. The MT300KA model included in our review has the following technical characteristics:

• power consumption 300 W;
• oscillation frequency from 10,000 to 22,000 counts/min;
• oscillation angle 2.8°;
• mains power;
• weight 1.58 kg.

First of all, this device is notable for two things. The first is the high reliability of operation, confirmed by the results of the 96-hour ABR test (a special test for wear resistance of power tools). The second is the Superlok system, which provides the ability to change nozzles without a special hex key.

The main advantage of the Superlok system was the ability to use an adapter for attaching nozzles from other manufacturers (Bosch, Makita, etc.). This approach to equipment makes the B&D multitool as versatile as possible. The ability to install high-quality accessories from competitors turns their advantages into the dignity of your tool.

On the MT300KA model, the problem of removing dust when using a multi-tool as a grinder is interestingly solved. On the sole of the trapezoidal nozzle, a mount for a dust tube is provided. At the opposite end of the tube there is a universal adapter for a household vacuum cleaner hose.

Despite the applied innovations and successful technical solutions, Black & Decker has a small drawback. The weight of 1.58 kg is quite a lot for such a tool. The manufacturer tried to compensate for the excess weight with the convenience of the handle, but in the case of work on an outstretched arm or in cramped conditions, a lot of weight makes itself felt.

Also, complaints from users are caused by a high level of noise. Although the manufacturer's claimed readings of 90 dB are not critical for the human ear, it is very unpleasant to work with a tool paired with a vacuum cleaner without protective headphones.

Bosch PMF 250 CES 0603100620

Producer: "Robert Bosch GmbH", Germany

High quality materials, attention to detail, a meticulous approach to assembly and a developed service network - these indicators have made a reputation for Bosch equipment. Our today's review includes an oscillator in a green case PMF 250 CES. Its main technical characteristics:

• power consumption 250 W;
• oscillation frequency from 15,000 to 20,000 counts/min;
• oscillation angle 2.8°;
• mains power;
• weight 1.3 kg.

The green case indicates that the model belongs to the Bosch household tool series. Therefore, it is supposed to be compared with analogues of the same class. But the analogues are much cheaper, it is hard to call the PMF 250 CES a low-cost model. The reason for the relatively high cost is in the tooling.

Usually the weakest point of a household multi-tool is the nozzles. Low wear resistance and, as a result, the need for frequent replacement lead to unexpected costs. But, according to users on the network, everything is different with Bosch nozzles.

With a weight of only 1.3 kg and an additional handle, the oscillator can be used for long periods of work without fatigue. According to user reviews, the multitool is very well balanced and the degree of side vibration during operation is minimal.

A special oscillating mechanism control system (Constant Electronic) ensures a constant level of output power, regardless of the load on the cutting tool. Although even with this system, power is often not enough, and this is a minus.

The Bosch PMF 250 CES cannot be unequivocally called a tool for domestic use. This model is a transitional step between a purely home power tool and specialized construction equipment. Bosch has an impressive "margin of safety", which, with a reasonable approach, allows you to use it even as a professional power tool.

AEG OMNI 300 KIT1 Price from 4 299 up to 6 246 ₴ →

Producer: "AEG Power Tools", Germany (Poland)

The AGE OMNI oscillating base is a universal platform with the ability to connect various attachments (sanding platform, drill or jigsaw). The model is presented on the market in several modifications, which differ primarily in the configuration.

So, modification AEG OMNI 300 KIT1 Price from 4 299 up to 6 246 ₴ has: deltoid grinding platform (OMNI-MT); set of abrasive sheets; set of saw nozzles; carrying bag.

Model AEG OMNI 300 KIT4 has: deltoid grinding platform (OMNI-MT); drill/driver (OMNI-RAD); jigsaw (OMNI-JS); set of abrasive sheets; set of saw nozzles; carrying bag.

The main advantage of AEG OMNI 300 KIT4 is time saving. You use three tools almost simultaneously. Replacement of nozzles is carried out by a simple movement of the hand within a few seconds.

AEG have created a versatile tool for professional use. Its main advantages: quick and reliable change of nozzles (grinding, drill, jigsaw), the ability to easily replace graphite brushes, the body is made of high-strength plastic; illumination of the working area, four metres of cable are provided. All this suggests that the tool is intended for active use.

Do not forget that the multitool is slower than a jigsaw, weaker than a grinder and cannot be compared with a full-fledged drill. The oscillating tool is designed to perform auxiliary work. Elimination of flaws made during the repair, dismantling of floor coverings, repair or replacement of tiles, fitting, finishing, grinding - this is where the AEG OMNI 300 KIT will be most in demand and effective.

Bosch GOP 10.8 V-LI Professional 060185800C

Producer: "Robert Bosch GmbH", Germany

In the segment of professional construction tools, the German company Bosch is traditionally one of the leaders. Thanks to the original technical solution, the blue Bosch deservedly got into our TOP-5. Using a battery as a power source has made the oscillating tool even more versatile and easy to use. The main characteristics of the model are as follows:

• oscillation frequency from 5000 to 20000 counts/min;
• battery powered;
• oscillation angle 2.8°;
• weight 1.0 kg.

Minimum weight (1 kg) and small dimensions (length 280 mm) are the distinguishing features of the Bosch oscillator. Such "modest" dimensions facilitate the work, and the high functionality of the multitool speeds up its execution.

The oscillator comes with an extensive set of nozzles. The tool attachment angle can be changed in the range from 0° to 240°. The markings in the form of a scale applied to the saw nozzles help to control the depth of cut. Fastening of abrasive cloths to a grinding nozzle is carried out by means of a flypaper.

The battery deserves special attention. The oscillator is equipped with two batteries to ensure uninterrupted operation of the instrument. This model uses the Bosch Electronic Cell Protection (ECP) system, which allows you to: recharge the battery at any time, avoid battery overload, prevent deep discharge, protect the battery from overheating.

An indicator scale is placed on the case, showing the battery charge level. Thanks to this improvement, a dead battery will not take you by surprise. Another handy little thing: Bosch Hyper Charge is the original recharging technology. In half the time required for a full charge, the battery receives 75% of the energy.

The Bosch multifunctional tool can be a great assistant for a professional builder.