Comparison Akaso Brave 7 vs LAMAX X7.1

The level of dust and water protection provided by the body of the camera itself. Most action cameras are designed for recording in extreme conditions, but the level of protection of each model can vary significantly — from the ability to shoot in the rain, to full tightness, allowing for a long immersion under water.

To characterize the security level of the camera, the international IP classification is used. Each device is assigned a code of the form IPXX, where instead of the first X — the level of protection against the ingress of foreign objects (including dust), and instead of the second X — the level of protection against the ingress of water.

Levels of protection against dust and foreign objects in modern action cameras are never lower than 5 — lower protection classes would provide unacceptably large gaps in the body. Specifically, level 5 provides that dust can get inside in small quantities, but does not affect the performance of the device. A higher level — 6 — provides full dustproof.

To characterize the level of protection from water, the following classification is used:

0 — no protection;
1 — drops of water falling at a right angle relative to the operating position of the device cannot cause dangerous consequences;
2 — protection against drops falling on the equipment at an angle of up to 15°;
3 — at an angle up to 60° (splash protection, minimum rain protection);
4 — protection from rai...n with strong wind;
5 — protection against water jets falling at any angle (water jets, for example, from a hose or heavy rain cannot harm the device);
6 — from temporary flooding;
7 — from temporary immersion under water to a depth of not more than 1 metre;
8 — from prolonged diving to depth (maximum time and depth are specified by the manufacturer separately).

In some cases, a model may only be IP-certified for one type of protection (only against sand or water). In this case, instead of the second parameter, simply X is put. So, for example, IPX6 security means that the camera is protected from temporary flooding and heavy rain, but the level of protection from dust is not defined and, accordingly, is not certified.

It is important to note that this parameter characterizes the protection of the camera itself, but does not take into account the capabilities of protective cases. Do not confuse it with the protection of the outer case, which sometimes comes with the device (see "Dust-, moisture-proof of case").

The degree of dust and water protection of the protective case supplied with the camera.

Protected case will save your camera from dust, water, temperature changes, shocks, etc. The specific degree of protection is indicated according to the international IP (Ingress Protection Rating) system, according to which each device is assigned a code of the form IPXX, where X is replaced by specific numbers. The first of them characterizes the protection against the penetration of foreign objects (from 0 to 6, where 0 is no protection). Usually, in boxes for action cameras, this indicator does not go below 5, because otherwise the container would have too large gaps, and its use simply would not make sense. Level 5 provides dust resistance — dust can get inside the case, but in small quantities that do not affect the device inside. Level 6 corresponds to complete imperviousness to dust.

The second digit is protection against liquid ingress (from 0 to 8, where 0 is no protection). Usually, the minimum level of protection against water is 6.

6 — protection against short-term immersion (for example, falling into a sea wave);
7 — protection against temporary immersion under water (up to 30 minutes) to a shallow depth (up to 1 metre), without continuous operation in immersed mode;
8 — protection against immersion to a depth of more than 1 metre for a time of more than 30 m, with the possibility of continu...ous operation underwater. The specific level of protection of level 8 can be quite impressive — up to the possibility of diving to several tens of metres.

Note that protective cases for action cameras can be sold separately. Therefore, if the capabilities of the complete container do not suit you, there may be a more secure case on the market. On the other hand, in general, it is still more convenient to buy such an accessory immediately with a camera — so as not to waste time and effort on choosing the right protective case.

The number of megapixels in the action camera sensor, in other words, the resolution of this sensor(1 megapixel is 1 million photosensitive points).

There is an opinion that the higher the resolution, the better the image quality. It is true from the point of view that manufacturers are trying to install high-resolution sensors in advanced cameras. At the same time, there are no strict dependencies here, and from the technical point of view, the number of megapixels determines only the maximum image resolution that can be captured using this sensor. The quality of this picture will depend both on several features of the sensor itself (size, type, special design solutions), and the specs of the camera. So when choosing, you should focus not so much on the resolution of the image sensor, but on the general class of the camera and reviews with examples of footage.

Additional information regarding the sensor installed in the lens. This item can specify both the diagonal size (in inches) and the sensor model, and sometimes both parameters at once. Anyway, such data is provided only if the device is equipped with a high-class image sensor. With the model, everything is quite simple: knowing the name of the sensor, you can find detailed data on it.

The diagonal of the image sensor is traditionally indicated in fractions of an inch — accordingly, for example, a 1/2.3" sensor will be larger than 1/2.6". Larger sensors are considered more advanced, as they allow for better image quality at the same resolution. This is because due to the larger sensor area, each pixel is also larger and receives more light, which improves sensitivity and reduces noise. Of course, the actual image quality will also depend on several other parameters, but in general, a larger sensor size usually means a more advanced camera.

— Photo during video. The ability to take photos directly while recording a video — usually using a separate button. Thus, it is convenient to fix the most significant moments of what is happening. Such photos are much better in quality than "freeze frames" from the captured video.

— Serial photo shoot. This feature allows you to take several pictures at once in a short period (usually it is a fraction of a second). A series of shots increases the chance of capturing a good moment, which can be very important given the specifics of using action cameras.

— One click recording. The ability to quickly turn on the camera for recording — literally at the touch of a button, by the name. Moreover, such a button works even if the device is turned off. However, the recording inevitably starts with some delay; but often this delay is a fraction of a second.

— Online streaming. Ability to stream video to popular services like YouTube and social networks (Facebook, Instagram, TikTok, etc.). Usually, the online streaming function is implemented when the action camera is connected to the Internet via a Wi-Fi network, less often via a wired connection. Communication with the World Wide Web can be held directly or through a smartphone or computer. It will require the use of appropriate software.

— <...a href="/en/list/695/pr-18957/">Time lapse. A special mode of operation of the action camera, in which video recording is carried out at a slower frequency is mainly used for filming slow processes. Thus, for example, a long journey or a long sunset can fit into a 3-minute video.

— Auto-rotate. The function of automatic rotation of the captured photos and videos to the position corresponding to the position of the camera. Without this feature, all footage during playback would be displayed strictly in landscape orientation, and footage shot with the camera upside down or upside down would have to be rotated in a photo or video editor. Usually, at the beginning of video recording, auto-rotation is blocked — so that the position of the frame at any time corresponds to the rotation of the camera itself relative to its original position.

— Photo panoramas shooting. The ability to use the camera to take panoramic photos. In traditional action cameras (see "Product type"), such shooting is carried out as follows: the camera takes several separate photos, which are then glued into one image. Regarding panoramic and 360-degree models (see ibid.), it is worth noting that not all such models support shooting in panoramic format, so it is advisable to check the availability of this function separately.

— Key points labels. The ability to add special marks to the footage that indicate key moments. While viewing such videos, you can go directly to the labels — this is easier than manually searching for the right moment. This feature is especially useful when shooting long videos, as well as when numerous individual files. The label, usually, is placed right during the shooting by pressing a special button or by voice command.

— Night shooting. Special mode for recording in low light conditions. The specific implementation of this function may be different: in some models, the sensitivity of the sensor is increased, in others, shooting in the IR range is used. Accordingly, specific features may vary: not every camera with this function can shoot in complete darkness, and these nuances should be clarified separately.

— GPS module. Built-in satellite navigation module that allows you to determine the current coordinates of the device. Options for using data from GPS can be different: geotagging footage, recording travelled routes, determining the speed of movement, or even full-fledged navigation on the map.

— Wi-Fi module. The Wi-Fi wireless module in action cameras can be used in different formats: in some models, it is responsible for connecting to the Internet, in others it is for communicating with a smartphone or other gadget, in others both options are available at once. Anyway, the main use of this connection is to transfer footage to an external device or to the Internet (including broadcasting in the online streaming format, see “Filming capabilities”). In addition, more specific functions can be provided, for example, using a smartphone as an external viewfinder and remote control. Specific features of the use of Wi-Fi in each case should be clarified separately.

— Bluetooth. Direct wireless communication technology for exchanging information between two electronic devices. In action cameras, it is most often used to connect remote controls, selfie sticks and smartphones, which can also act as a remote control. Unlike the Wi-Fi module, it consumes battery power more economically, but at the same time, the range of wireless communication is reduce...d to 10 metres.

— NFC chip. NFC is a wireless communication technology over short distances (up to 10 cm). In action cameras, this technology is mainly used as an auxiliary one, to facilitate connection with a smartphone or other gadget via Wi-Fi or Bluetooth. If such a gadget is also equipped with NFC, just bring the camera to it and confirm the connection — it's easier than fiddling with the settings.

— USB-C. A relatively new type of USB interface that uses a miniature double-sided connector, slightly larger than microUSB. Most often used for similar purposes — as a universal connector through which you can charge the battery and connect the camera to a computer (for copying photos and videos, updating software, etc.). P.). At the same time, USB-C provides a higher data transfer rate than microUSB, supports more power supply, and also has a more convenient plug. Occasionally, there are more specific ways to use this interface — for example, direct connection to a smartphone or tablet that has a USB-C port.

— HDMI output. HDMI is a digital interface specially designed for high-definition video and multi-channel audio. With this output, you can connect the camera to a TV, monitor or other device as an external player and play the footage directly. The convenience of HDMI is that almost all modern video equipment with support for HD standards is equipped with such inputs.

Note that the cameras can be equipped with a smaller version of the connector — miniHDMI or microHDMI; however, finding an adapter cable is usually not a problem, it can even be supplied in the kit.

— AV output. Output for transmitting video and audio signals in analogue format. In action cameras, it most often has the form of a 3.5 mm mini-jack connector. The AV output capabilities are noticeably more modest than those of HDMI, which has a similar purpose: the analogue signal only allows standard definition video (not HD) plus mono or stereo sound (not multi-channel). On the other hand, often even such features are enough; and AV inputs are widespread and are found not only in modern but also in outdated technology like CRT TVs. In addition, many cameras have two video outputs at once — both HDMI and AV.

— Microphone connection. Almost any modern action camera has a built-in microphone that allows you to record sound. However, the quality of its sound is often quite low. Thus, many models can connect an external microphone — you can fix it, for example, on the helmet strap and record the comments of the athlete in the process of movement. Note that different types of connectors can be used for such a connection. As a result, the specific connector type and supported accessories depend on the action camera model, and some devices are only compatible with branded microphones.

— Diagonal. The larger the screen, the more convenient it is to watch (and also to control if the display is touch-sensitive). On the other hand, the diagonal of the built-in display directly affects the size of the case, and action cameras should be quite compact. Thus, there are practically no screens larger than 2.5" in modern action cameras.

— Resolution. Theoretically, the higher the resolution, the clearer and better image the screen produces. On the other hand, displays in action cameras are designed mainly for menu operation and footage preview — and for these purposes, especially high resolutions are not needed. For models with two screens, the rear display is considered the main display.

— Touch screen. Display equipped with a sensor and responsive to touch like in smartphones/tablets. Control through such a display is simpler and more intuitive than using buttons, rotary knobs, etc. On the other hand, for more or less convenient control, the touch screen must be quite large, which affects the dimensions of the entire camera.

— Front screen. The presence in the camera of a screen mounted on the front panel, next to the lens. Other displays may not be present at all; in such cases, the diagonal, resolution and other parameters are given for the front screen.

It is worth noting that most often the simplest black...-and-white displays are installed on the front panel, suitable only for text and basic graphic information. However, even on such a screen, you can display a wide variety of service data: the current mode of operation (photo, video, standby), the resolution used, the shooting time, the amount of free space on the drive, etc. But more advanced displays are not used as front displays: a full-colour screen is needed only for taking a selfie, and for this you can use a remote display with a remote control(see "Control") or a smartphone connected to the camera.

The ability to control the action camera using voice commands. Specific capabilities may vary (depending on the model), but even the simplest devices support the control of the basics of filming — the start and stop of recording. Some cameras can recognize a fairly extensive set of commands. Anyway, the main advantage of voice control is that it does not require hands. However, this feature significantly affects the cost. Besides, it has restrictions on languages — if English is almost guaranteed to be supported, then difficulties may arise with other languages.

— Protective case. A special container that provides additional protection against dust, moisture, shock, extreme temperatures and other similar “troubles”. The specific degree of protection in each case must be specified separately. In order not to interfere with the shooting, the box is made of transparent materials. In addition, we note that some cameras can only be mounted on mounts in a protective case (or in a mounting frame — see below), since the camera body may not have mounts for this.

— Curved mount(helmet). A mount designed to mount the camera on a helmet or other curved surface. The design of such a mount is based on a curved platform with an adhesive layer or hook-and-loop, the shape of which approximately corresponds to the shape of the surface of the helmet. Such a fixture can provide a more secure hold than the classic flat platform (see below).

— Flat mount. One of the basic and simplest mounts used to fix an action camera on almost any uniform surface: snowboard, skateboard, car hood, etc. It is a small flat platform, on one side of which the camera is attached, while the other is fixed on the desired surface (using hook-and-loop, special glue, etc.). Note that flat mounts are often used for mounting on a helmet. However, there is a separate type of mount for this, with a curved platform (see above).

— 3-axis mount. It differs from other types of mounting in the presence of three movable nodes that allow you to rotate the camera at an angle of up to 90 degrees in three axes. This allows you to choose the most interesting or successful shooting angle — on the side of the helmet, for example. Such options are usually compatible with many other mounts, so they can be used in conjunction with a handlebar, curved mount, etc.

— Bicycle/moto handlebar. Mount for installing the camera on a small pipe, such as the handlebars of a bicycle or motorcycle. Usually, it looks like a clamp, and the size of the fastening can be adjusted within a fairly wide range, adjusting it to pipes of different diameters.

— Suction cup(on glass). Camera mount, fixed in the right place with a suction cup. Allows you to install the device on flat and slightly curved surfaces. At the same time, note that such fasteners are not held as securely as flat or curved ones (see the relevant paragraphs). On the other hand, the suction cup is easy to attach and remove and leaves no marks. Therefore, mounts of this type are mainly used for installation on car glass when the camera works as a DVR.

— Clamp (clip). The clip-pin mount is quite versatile since it allows you to hang the camera on almost any suitable piece of equipment (backpack strap, unloading belt, belt, etc.). But at the same time, it is not very suitable for extreme shooting due to the relatively low reliability.

— Head mount. A device for fixing the camera on the head — usually on the forehead, like a headlamp. In addition to being hands-free, this placement has another advantage: the camera lens faces the same direction as the user. In this case, the mount itself is usually a system of elastic straps and is designed to be worn directly on the head, in contrast to the curved platform for the helmet. However, in some models, the possibility of putting on a helmet is also allowed.

— Chest mount. This mount is a system of elastic straps that allows you to fix the camera on the user's chest, shooting a little lower than the "eyeball". Like the head mount (see above), it easily adapts to the desired size.

— Mounting frame. A device designed to mount the camera on various mounts — helmet-mounted, on the handlebar, etc. The camera body itself often does not have mounts for such fixing, which is why you have to use additional equipment. Note that a similar function is often performed by a protective case(see above); the mounting frame, in contrast, provides almost no protection. However, in the frame, the camera body remains as open as possible. This provides additional features — in particular, it allows you to connect various cables and effectively use the built-in microphone, which is not possible with many protective cases.

— Monopod(selfie stick). It is a rod, usually folding, and sometimes adjustable in length; on one end of the rod is a mount for the camera and on the other — a handle for holding in your hand. By the name, such a monopod is intended mainly for filming itself — thanks to the length of the rod, the camera can be held at a convenient distance for this. However, other applications are also possible: for example, with the help of a monopod, you can “look” quite far over the edge of a cliff or around a corner. The main disadvantage of such a device is that one hand is constantly busy.

In addition to those mentioned above, other types of mounts may be included in the delivery package — for example, for musical instruments (for a guitar neck, a drum kit bar, etc.), for a surfboard, etc.